WiFi Client Scan & Connect - Error

1

I am attempting to connect to a WiFi access point but I have been having issues. The first time I was able to set the security and the passphrase but could not connect. I would consistently get an error or -6.

root@swi-mdm9x15:~# wifi client connect 0x10000001
ERROR: le_wifiClient_Connect returns error code -6
root@swi-mdm9x15:~#

I moved to another access point as I thought the issue might be the passphrase had spaces in it. With the spaces I was not sure how to set up teh pass phrase, do you need quotes or not and will it eve work if there are spaces. I tried with and without quotes but still got the -6 error.

When attempting on the second access point all I got when attempting a scan was:

root@swi-mdm9x15:~# wifi client scan
starting scan
DEBUG: le_wifiClient_GetFirstAccessPoint ERRORroot@swi-mdm9x15:~#

If there are any suggestions as to what I may have changed or done incorrectly I would appreciate the help.

Thankfully
Kas

1 Like
2

Hi Kas,

I tried the same commands and didnt run into any issues. Could you show your logread -f traces?

regards,
ashish

3

Hello @asyal,

I have attached my logread -f file and changed my password for security reasons but the overall form remains the same (The XXXXXX YYYYYY 123 PPPP). I hope this provides the information needed.

Thanks
Kas

Ps. where would I be able to find what the error codes mean.

logread_-f.txt (31.4 KB)

4

Hello @asyal,

Is there any further information regarding how I could resolve this issue or what the error means.

Thanks
Kas

5

Hi Kas,
@Kas.Lewis

I finally got some time to try this out.

The issue you saw might be due to the firmware version you might have on the module.
I was getting the same error as you but then I downloaded the latest firmware from:
http://source.sierrawireless.com/resources/legato/wpfirmwarerelease/

The commands worked as what was written in the doc on the network (note I changed the password I used)

wifi client start
wifi client scan
wifi client setsecurityproto 0x10000001 3
wifi client setpassphrase 0x10000001 password
wifi client connect 0x10000001

cheers,
Ashish

6

Hello @asyal,

Thank you for the response. I have updated my firmware to the most recent but I am still having issues. I have only tried it at one location. I will attempt a different router and internet provider tomorrow. The error is below in the screenshot.

2016-12-10 23_35_15-mangOH Dev using Legato 16.07 on Ubuntu 16.04.1 [Running] - Oracle VM VirtualBox.png837×205 43.3 KB

I will update as to m findings tomorrow but if you have any information as to what may be causing the current issue that would be great.

Thankfully
Kas

7

why does your legato version showed modified?
Here is what i see when i redownload the firmware:
root@swi-mdm9x15:~# cm info
Device: WP8548
IMEI: 359377060016051
FSN: LL604200070705
Firmware: SWI9X15Y_07.11.11.00 r33161 CARMD-EV-FRMWR1 2016/09/20 16:36:44
Bootloader: SWI9X15Y_07.11.11.00 r33161 CARMD-EV-FRMWR1 2016/09/20 16:36:44
root@swi-mdm9x15:~# legato version
16.07.0_5aabbe8a5c30c0b16469b0ea885a82f6
root@swi-mdm9x15:~# wifi client start
successfully called start
root@swi-mdm9x15:~# wifi client scan
No issues after this…

8

Hello @asyal,

The only modifications made were those listed in the blog I wrote on setting up the Legato environment. There should be nothing else. I did a repo sync as well to be sure everything was up to date and then rebuilt Legato before installing it again on the mangOH board after doing a fresh firmware update. Is there away to ensure a fresh Legato framework is installed with out creating a fresh new VM.

Thanks
Kas

9

can you do a firmware install only? Dont use the VM to download the mangoh/legato apps.
Basically, do firmware install for WP module from source
http://source.sierrawireless.com/resources/legato/wpfirmwarerelease/

Dont install any app from the VM and run the commands above.

10

Without running

cd mangOH/legato
make wp85
instlegato wp85 192.168.2.2

I can not ssh into the mangoh board. I just get a connection timed out error.

Kas

11

After reinstalling legato on the mangOH board it appears as though I can not SSH into teh board at all.

Kas

1 Like
12

why did you have re-install legato?
Just redownload the firmware from the source site I sent to you.
What do you see?

13

I tried that and I could not SSH into the mangOH board. I then attempted to run the instlegato command but that to says “Device address 192.168.2.2 seems to be unreachable”. I have also attempted to ping the mangOH board, this to gives 100% packet loss, “Destination host unreachable”.

I can not get access to the board for some reason. I have attempted to reseat the module, power cycled teh board numerous times. Nothing is showing signs of working.

Kas

14

Can you pull pin 7 on SW401 up and try to redowload the firmware?
If this doesnt work, you might need to use fwupdate tool in linux.

15

I have attempted to flash the firmware with SW 7 in the on position and then power cycle the board. Both before and after cycling the board I was unable to ping the board.

I also moved SW back to off and I still cannot ping the board. Any access via 192.168.2.2 does not appear to work.

Kas

16

Is there anything else to try at this point or is the board somehow bricked/dead ? The board has been either on the same table the whole time or in the anti-static bag it comes in. Any information on how to possibly proceed with this board would be helpful.

Thanks
Kas

2016-12-14 00_31_05-Select C__Users_Kas_AppData_Local_Temp_RarSFX0_fdt.exe.png484×511 10.6 KB

Still cant connect to the board via SSH even with a successful firmware update :frowning:

17

I have asked internally…There is a way to not have this error if you use a linux machine.
Need to check on windows. will get back to you

18

Hi Kas,

Have you tried connecting to the RS232 Console Port (UART 2) on mangOH? This way you can monitor the the Linux/Legato boot process - you might get some clues as to what’s happening from here.

I once had an issue where I couldn’t SSH into the modem after incorrectly editing a file on the WP8548 which prevented it from starting a few important services, including SSH. As a result, I couldn’t SSH into it nor did I know what was going on until I monitored the boot process on the Console port. I was able to log in via the Console port, edit the file (correctly this time) then reboot to restore it.

Just a thought.

Cheers,
Raf

19

Hi Kas,

As suggested by Raf, could you share the kernel log message on the RS232 port?
This will give us an idea what went wrong with your unit.

regards,
Ashish

20

1 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache
[ 0.000000] Machine model: QCT MSM9615 CDP
[ 0.000000] memory pool 3 (start 4ff00000 size 100000) initialized
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x00540000, Cache siz e: 262144 B
[ 0.000000] socinfo_init: v7, id=106, ver=3.0, raw_id=1760, raw_ver=1760, hw_ plat=0, hw_plat_ver=65536
[ 0.000000] accessory_chip=0, hw_plat_subtype=0, pmic_model=19, pmic_die_rev ision=3
[ 0.000000] CPU: All CPU(s) started in SVC mode.
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 40720
[ 0.000000] Kernel command line: console=ttyHSL0,115200 console=ttyHSL1,1152 00 fudge_ro_rootfs=true rootfs_ro=true mtdparts=msm_nand:0x00100000@0x051c0000(b ootloader),0x01400000(kernel),0x03140000(rootfs),0x02780000(user0),0x08b80000(us er1),0x00500000(user2),0x00200000(user3) androidboot.serialno=MDM9615 lkversion= 1.3.0_a50272dbb2 androidboot.baseband=msm
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] allocated 507904 bytes of page_cgroup
[ 0.000000] please try ‘cgroup_disable=memory’ option if you don’t want memor y cgroups
[ 0.000000] Memory: 150472K/164864K available (6762K kernel code, 631K rwdata , 2256K rodata, 1366K init, 1265K bss, 14392K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0000000 - 0xff000000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xcf800000 ( 248 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc08d69e0 (9019 kB)
[ 0.000000] .init : 0xc08d7000 - 0xc0a2cb6c (1367 kB)
[ 0.000000] .data : 0xc0a2e000 - 0xc0acbf7c ( 632 kB)
[ 0.000000] .bss : 0xc0acbf7c - 0xc0c084bc (1266 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:681
[ 0.000030] sched_clock: 32 bits at 32kHz, resolution 30520ns, wraps every 65 542000541696ns
[ 0.000610] Console: colour dummy device 80x30
[ 0.000701] Calibrating delay loop… 366.18 BogoMIPS (lpj=1830912)
[ 0.060491] pid_max: default: 32768 minimum: 301
[ 0.060949] Security Framework initialized
[ 0.061040] Smack: Initializing.
[ 0.061468] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.061498] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.063268] Initializing cgroup subsys debug
[ 0.063299] Initializing cgroup subsys memory
[ 0.063360] Initializing cgroup subsys devices
[ 0.063390] Initializing cgroup subsys freezer
[ 0.063390] Initializing cgroup subsys net_cls
[ 0.063421] Initializing cgroup subsys blkio
[ 0.063482] CPU: Testing write buffer coherency: ok
[ 0.063604] ftrace: allocating 22813 entries in 67 pages
[ 0.145429] Setting up static identity map for 0x40e1e180 - 0x40e1e1d8
[ 0.169327] devtmpfs: initialized
[ 0.178818] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1
[ 0.181474] regulator-dummy: no parameters
[ 0.182054] NET: Registered protocol family 16
[ 0.183244] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.183488] AXI: msm_bus_fabric_init_driver(): msm_bus_fabric_init_driver
[ 0.185045] msm_serial_hsl_init: driver initialized
[ 0.185808] cpuidle: using governor ladder
[ 0.185838] cpuidle: using governor menu
[ 0.186571] msm_rpm_init: RPM firmware 3.0.16842958
[ 0.186815] gpio_cf3_low_power_reset_toggle: Setting up LowPower_RESET pin to ggle timer
[ 0.186845] unmatched machine ID in register_i2c_devices
[ 0.186876] wl18xx board initialization done
[ 0.187395] 8018_s1: 500 <–> 1150 mV at 1150 mV normal idle
[ 0.187822] 8018_s2: 1225 <–> 1300 mV at 1300 mV normal idle
[ 0.188707] 8018_s3: 1800 mV normal idle
[ 0.189226] 8018_s4: 2100 <–> 2200 mV at 2200 mV normal idle
[ 0.190050] 8018_s5: 1350 mV normal idle
[ 0.190965] 8018_l2: 1800 mV normal idle
[ 0.191851] 8018_l3: 1800 mV normal idle
[ 0.192278] 8018_l4: 3300 mV normal idle
[ 0.192675] 8018_l5: 2850 mV normal idle
[ 0.193041] 8018_l6: 1800 <–> 2850 mV at 2850 mV normal idle
[ 0.193468] 8018_l7: 1850 <–> 1900 mV at 1900 mV normal idle
[ 0.193560] 8018_l7: supplied by 8018_s4
[ 0.193926] 8018_l8: 1200 mV normal idle
[ 0.194048] 8018_l8: supplied by 8018_s3
[ 0.194414] 8018_l9: 750 <–> 1150 mV at 1150 mV normal idle
[ 0.194506] 8018_l9: supplied by 8018_s5
[ 0.194903] 8018_l10: 1050 mV normal idle
[ 0.194994] 8018_l10: supplied by 8018_s5
[ 0.195452] 8018_l11: 1050 mV normal idle
[ 0.195544] 8018_l11: supplied by 8018_s5
[ 0.195971] 8018_l12: 1050 mV normal idle
[ 0.196062] 8018_l12: supplied by 8018_s5
[ 0.196490] 8018_l13: 1850 <–> 2950 mV at 2950 mV normal idle
[ 0.196886] 8018_l14: 2850 mV normal idle
[ 0.197253] 8018_lvs1: no parameters
[ 0.197344] 8018_lvs1: supplied by 8018_s3
[ 0.197741] vdd_dig_corner: 0 <–> 0 mV at 0 mV
[ 0.205005] ext_2p95v: no parameters
[ 0.205249] gpio_vreg_probe: id=18, name=ext_2p95v, gpio=18, gpio_label=ext_2 p95_en
[ 0.205768] pm8018_probe: PMIC revision 1: F3
[ 0.205798] pm8018_probe: PMIC revision 2: 08
[ 0.205829] pm8018_probe: PMIC version: PM8018 rev 2.1
[ 0.205829] pm8018_probe: PMIC Restart Reason: Triggered from KPD (power key press)
[ 0.207324] pm_gpio_probe: OK: base=88, ngpio=6
[ 0.207874] pm8xxx_mpp_probe: OK: base=94, ngpio=6
[ 0.209980] msm_serial_hsl_probe: ttyHSL0 is disabled.
[ 0.210041] msm_serial_hsl: probe of msm_serial_hsl.0 failed with error -1
[ 0.210499] msm_serial_hsl_probe: ttyHSL1 is reserved for CONSOLE service.
[ 0.210499] msm_serial_hsl_probe: detected port #1 (ttyHSL1)
[ 0.210773] msm_serial_hsl.1: ttyHSL1 at MMIO 0x16440000 (irq = 186, base_bau d = 460800) is a MSM
[ 0.210895] msm_hsl_console_setup: console setup on port #1
[ 0.315122] gpio_cf3_low_power_reset_timer_callback: LowPower_RESET pin toggl ed high
[ 0.315153] gpio_cf3_low_power_reset_timer_callback: LowPower_RESET pin toggl e timer deleted
[ 0.840805] console [ttyHSL1] enabled
[ 0.856218] cpufreq_table_init: CPU: 4 scaling frequencies supported.
[ 0.862200] hw-breakpoint: Debug register access (0xee003e17) caused undefine d instruction on CPU 0
[ 0.870654] hw-breakpoint: CPU 0 failed to disable vector catch
[ 0.877216] socinfo_init_dev: device_register fail (-22)
[ 0.884480] sps:REVISION of BAM 0xd0060000 is 0x5.
[ 0.888448] sps:BAM 0x12244000 is registered.
[ 0.892781] sps:sps is ready.[ 1.187273] NET: Registered protocol family 2
[ 1.192614] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 1.198596] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 1.205005] TCP: Hash tables configured (established 2048 bind 2048)
[ 1.211353] TCP: reno registered
[ 1.214466] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 1.220326] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
vice ac
[ 2.020204] Setting mtd->writebufsize to 0x800
[ 2.024629] Found a supported NAND device
[ 2.028567] NAND Controller ID : 0x4030
[ 2.032443] NAND Device ID : 0x1590ac2c
[ 2.036288] Buswidth : 8 Bits
[ 2.039249] Density : 512 MByte
[ 2.042484] Pagesize : 2048 Bytes
[ 2.045780] Erasesize: 131072 Bytes
[ 2.049229] Oobsize : 64 Bytes
[ 2.052372] CFG0 Init : 0xa8d408c0
[ 2.055821] CFG1 Init : 0x0004745c
[ 2.059301] ECCBUFCFG : 0x00000203
[ 2.062810] CW size : 528 bytes
[ 2.066168] BCH ECC : disabled
[ 2.069525] 7 cmdlinepart partitions found on MTD device msm_nand
[ 2.075568] Creating 7 MTD partitions on “msm_nand”:
[ 2.080512] 0x0000051c0000-0x0000052c0000 : “bootloader”
[ 2.088936] 0x0000052c0000-0x0000066c0000 : “kernel”
[ 2.110361] 0x0000066c0000-0x000009800000 : "rootfs"
registered new interface driver dm9601
[ 2.382206] usbcore: registered new interface driver smsc75xx
[ 2.387883] usbcore: registered new interface driver smsc95xx
[ 2.393590] usbcore: registered new interface driver net1080
[ 2.399206] usbcore: registered new interface driver cdc_subset
[ 2.405127] usbcore: registered new interface driver zaurus
[ 2.410743] usbcore: registered new interface driver MOSCHIP usb-ethernet dri ver
[ 2.418068] usbcore: registered new interface driver int51x1
[ 2.423775] usbcore: registered new interface driver cdc_ncm
[ 2.429238] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 2.449656] msm_hsusb_host msm_hsusb_host: unable to find transceiver
[ 2.468426] platform msm_hsusb_host: Driver msm_hsusb_host requests probe def erral
[ 2.488295] msm_hsic_host msm_hsic_host: Qualcomm EHCI Host Controller using HSIC
[ 2.494948] msm_hsic_host msm_hsic_host: new USB bus registered, assigned bus number 1
[ 2.529986] msm_hsic_host msm_hsic_host: irq 264, io mem 0x12540000
[ 2.549916] msm_hsic_host msm_hsic_host: USB 2.0 started, EHCI 1.00
[ 2.557515] hub 1-0:1.0: USB hub found
[ 2.560445] hub 1-0:1.0: 1 port detected
[ 2.566183] usbcore: registered new interface driver cdc_acm
[ 2.570944] cdc_acm: USB Abstract Control Model driver for USB modems and ISD N adapters
[ 2.579124] usbcore: registered new interface driver usbserial
[ 2.584831] usbcore: registered new interface driver ftdi_sio
[ 2.590477] usbserial: USB Serial support registered for FTDI USB Serial Devi ce
[ 2.597894] usbcore: registered new interface driver option
[ 2.603326] usbserial: USB Serial support registered for GSM modem (1-port)
[ 2.610437] usbcore: registered new interface driver qcserial
[ 2.615992] usbserial: USB Serial support registered for Qualcomm USB modem
[ 2.622981] usbcore: registered new interface driver sierra
[ 2.628444] usbserial: USB Serial support registered for Sierra USB modem
[ 2.635281] usbcore: registered new interface driver GobiSerial
[ 2.641171] usbserial: USB Serial support registered for GobiSerial
[ 2.647428] usbcore: registered new interface driver usb_ehset_test
[ 2.653685] msm_otg msm_otg: msm_otg probe
[ 2.657652] msm_otg msm_otg: failed to get phy_clk
[ 2.662810] msm_otg msm_otg: OTG regs = d006e000
[ 2.669800] misc usb_link: registered misc device minor 47
[ 2.678406] mbim_init: initialize 1 instances
[ 2.682252] mbim_init: Initialized 1 ports
[ 2.691377] rndis_qc_init: initialize rndis QC instance
[ 2.697054] android_usb gadget: android_usb ready
[ 2.702273] input: pmic8xxx_pwrkey as /devices/platform/msm_ssbi.0/pm8018-cor e/pm8xxx-pwrkey/input/input0
[ 2.713383] rtc-pm8xxx rtc-pm8xxx: rtc core: registered pm8xxx_rtc as rtc0
[ 2.719578] i2c /dev entries driver
[ 2.724309] pm8xxx-adc supply pa_therm not found, using dummy regulator
[ 2.730444] swimcu_hwmon_probe: start
[ 2.733862] swimcu_hwmon_probe: success num 2
[ 2.762368] pm8xxx_tm_probe: OK
[ 2.765298] usbcore: registered new interface driver usbhid
[ 2.770120] usbhid: USB HID core driver
[ 2.775339] usbcore: registered new interface driver snd-usb-audio
[ 2.782664] voice_allocate_shared_memory: ION memory allocation failed
[ 2.788585] msm_pcm_probe: dev name msm-voip-dsp
[ 2.793407] msm_pcm_probe: dev name msm-host-pcm-voice
[ 2.799175] msm_pcm_probe: dev name msm-pcm-dsp
[ 2.803021] msm_pcm_probe: dev name msm-multi-ch-pcm-dsp
[ 2.809613] mdm9615_audio_init(): Interface Type (wm8944) = 1
[ 2.815931] mdm9615_audio_init - AR8, AR755xRD and CF3 configuration
[ 2.821669] soc-audio soc-audio.0: ASoC: machine mdm9615-wm8944-snd-card shou ld use snd_soc_register_card()
[ 2.850541] soc-audio soc-audio.0: snd-soc-dummy-dai <-> MultiMedia1 mapping ok
[ 2.857286] soc-audio soc-audio.0: snd-soc-dummy-dai <-> MultiMedia2 mapping ok
[ 2.864581] soc-audio soc-audio.0: snd-soc-dummy-dai <-> CS-VOICE mapping ok
[ 2.871814] soc-audio soc-audio.0: snd-soc-dummy-dai <-> VoIP mapping ok
[ 2.878132] soc-audio soc-audio.0: msm-stub-rx <-> msm-dai-q6.241 mapping ok
[ 2.885243] soc-audio soc-audio.0: msm-stub-tx <-> msm-dai-q6.240 mapping ok
[ 2.892354] soc-audio soc-audio.0: snd-soc-dummy-dai <-> SLIMBUS0_HOSTLESS ma pping ok
[ 2.900137] soc-audio soc-audio.0: snd-soc-dummy-dai <-> AUXPCM_HOSTLESS mapp ing ok
[ 2.907767] soc-audio soc-audio.0: snd-soc-dummy-dai <-> VoLTE mapping ok
[ 2.914603] soc-audio soc-audio.0: snd-soc-dummy-dai <-> DTMF_RX_HOSTLESS map ping ok
[ 2.922173] soc-audio soc-audio.0: msm-stub-tx <-> msm-dai-stub mapping ok
[ 2.929009] soc-audio soc-audio.0: msm-stub-tx <-> msm-dai-stub mapping ok
[ 2.935785] usb 1-1: new high-speed USB device number 2 using msm_hsic_host
[ 2.942896] soc-audio soc-audio.0: msm-stub-rx <-> msm-dai-stub mapping ok
[ 2.949671] soc-audio soc-audio.0: msm-stub-tx <-> msm-dai-stub mapping ok
[ 2.956844] soc-audio soc-audio.0: msm-stub-rx <-> msm-dai-stub mapping ok
[ 2.963375] soc-audio soc-audio.0: msm-stub-rx <-> msm-dai-q6.224 mapping ok
[ 2.970364] soc-audio soc-audio.0: msm-stub-tx <-> msm-dai-q6.225 mapping ok
[ 2.977353] soc-audio soc-audio.0: msm-stub-rx <-> msm-dai-q6.32773 mapping o k
[ 2.984800] soc-audio soc-audio.0: msm-stub-tx <-> msm-dai-q6.32772 mapping o k
[ 2.992064] soc-audio soc-audio.0: msm-stub-tx <-> msm-dai-q6.32771 mapping o k
[ 3.000457] hub 1-1:1.0: USB hub found
[ 3.003418] soc-audio soc-audio.0: msm-stub-rx <-> msm-dai-q6.2 mapping ok
[ 3.010102] hub 1-1:1.0: 3 ports detected
[ 3.014771] soc-audio soc-audio.0: msm-stub-tx <-> msm-dai-q6.3 mapping ok
[ 3.023805] soc-audio soc-audio.0: wm8944-hifi <-> msm-dai-q6.0 mapping ok
[ 3.029879] soc-audio soc-audio.0: wm8944-hifi <-> msm-dai-q6.1 mapping ok
[ 3.052067] TCP: cubic registered
[ 3.054417] NET: Registered protocol family 17
[ 3.059484] Registering SWP/SWPB emulation handler
[ 3.070715] clock_late_init() disabled 39 unused clocks
[ 3.077430] sps:BAM 0x124c2000 is registered.
[ 3.086525] no pmic restart interrupt specified
[ 3.090401] MSM Watchdog Initialized
[ 3.097329] ext_2p95v: disabling
[ 3.099649] regulator-dummy: disabling
[ 3.117259] msm_otg msm_otg: phy_reset: success
[ 3.121959] rtc-pm8xxx rtc-pm8xxx: setting system clock to 1970-01-01 00:02:0 9 UTC (129)
[ 3.133557] ### dt-test ### No testcase data in device tree; not running test s
[ 3.146253] ALSA device list:
[ 3.150373] #0: mdm9615-wm8944-snd-card
[ 3.165359] Freeing unused kernel memory: 1364K (c08d7000 - c0a2c000)
[ 3.710178] usb 1-1.3: new high-speed USB device number 4 using msm_hsic_host
[ 3.742347] hub 1-1.3:1.0: USB hub found
[ 3.745643] hub 1-1.3:1.0: 5 ports detected
[ 3.753090] ubi0: scanning is finished
[ 3.764504] ubi0 warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 58, need 80
[ 3.776072] ubi0: attached mtd2 (name “rootfs”, size 49 MiB)
[ 3.780772] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 3.787578] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 3.794353] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 3.801281] ubi0: good PEBs: 394, bad PEBs: 0, corrupted PEBs: 0
[ 3.807263] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 12 8
[ 3.814497] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequ ence number: 2264427
[ 3.823409] ubi0: available PEBs: 0, total reserved PEBs: 394, PEBs reserved for bad PEB handling: 58
[ 3.832565] ubi0: background thread “ubi_bgt0d” started, PID 77
UBI device number 0, total 394 LEBs (50028544 bytes, 47.7 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 3.871204] block ubiblock0_0: created from ubi0:0(rootfs)
rootfs: dev ‘/dev/ubiblock0_0’ 'squashfs’
S02mount_early: Executing mount_early_user_start…
S02mount_early: Trying to mount UBIFS on /mnt/flash using [usrquota,grpquota,rw] mount options…
[ 6.595879] ubi2: scanning is finished
[ 6.598718] ubi2 error: ubi_read_volume_table: the layout volume was not foun d
[ 6.606683] ubi2 error: ubi_attach_mtd_dev: failed to attach mtd4, error -22
ubiattach: error!: cannot attach mtd4
error 22 (Invalid argument)
S02mount_early: Unable to attach mtd partition user1 to UBI logical device 2
S02mount_early: Trying to mount UBIFS on /mnt/flash using [rw] mount options…
SSS▒▒S▒▒▒2 error: ubi_attach_mtd_dev: failed to attach mtd4, error -22
ubiattach: error!: cannot attach mtd4
error 22 (Invalid argument)
PuTTYS02mount_early: Unable to attach mtd partition user1 to UBI logical device 2
[ 8.028597] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 8.039737] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 8.045811] ubi1: good PEBs: 316, bad PEBs: 0, corrupted PEBs: 0
[ 8.051915] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 12 8
[ 8.058873] ubi1: max/mean erase counter: 1/0, WL threshold: 4096, image sequ ence number: 292670867
[ 8.067968] ubi1: available PEBs: 0, total reserved PEBs: 316, PEBs reserved for bad PEB handling: 80
[ 8.077155] ubi1: background thread “ubi_bgt1d” started, PID 178
UBI device number 1, total 316 LEBs (40124416 bytes, 38.3 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
[ 8.121562] block ubiblock1_0: created from ubi1:0(legato)
sd_mod [ 8.961330] usbcore: registered new interface driver usb-storage
msm_sdcc ▒▒▒: RmNet(1) dual Speed, IN:ep10in OUT:ep7out
[ 10.066564] apr_tal: SMD_EVENT_OPEN
[ 10.069403] Match for Function Name: audio, Int #16
[ 10.074042] Match for Function Name: audio, Int #17
[ 10.078773] Match for Function Name: audio, Int #18
[ 10.083931] ecm_native_function_bind_config: ecm_native_function_bind_config MAC: 00:00:00:00:00:00
[ 10.092904] android_usb gadget: using random self ethernet address
[ 10.110849] usb0: MAC 2e:50:5b:e9:8a:20
[ 10.113688] usb0: HOST MAC 9a:93:aa:54:b1:12
[ 10.117961] Match for Function Name: cdc_ethernet, Int #19
[ 10.150038] Match for Function Name: cdc_ethernet, Int #20
[ 10.157637] msm_otg msm_otg: Avail curr from USB = 2
[ 10.161635] ci_hdrc ci_hdrc.0: CI_HDRC_CONTROLLER_SUSPEND_EVENT received
Starting syslogd/klogd: Starting diagrebootapp: [ 11.274500] nmea: smd opened
Sending discover…
Starting qmuxd: Starting mbimd: Starting tcf-agent: run_getty.sh: UART2 (=/dev/t tyHSL0) reserved for CONSOLE
[ 28.824538] PM: Syncing filesystems … noirq resume of devices complete afte r 1.281 msecs
[ 28.954402] PM: early resume of devices complete after 1.587 msecs
[ 28.955653] msm_hsic_host msm_hsic_host: HSIC-USB exited from low power mode
[ 28.994414] PM: resume of devices complete after 39.981 msecs
[ 29.075507] Restarting tasks …
[ 29.085457] mbim_read: Requests list is empty. Wait.
[ 29.112498] done.