Hello
This morning my MangOH, seem’s have a problem.
When I startup, the MangOH reboot main time and return to the firmware version.
My configuration was:
- Install sierra firmware WP77xx_Release13_GENERIC_GCF.spk
- Compile and install mangOH Git (https://github.com/mangOH/mangOH) with leaf swi-wp77_4.0.0
- Compile and Install my application.
But now when a boot my MangOH, i’ve only the firmware.
I tried to install again the mangOH git, but the mangOH return after main reboot to the firmware version.
If you have a Idea …
The console Log:
Starting Dropbear SSH server: dropbear.
run_getty.sh: ttyHSL1 reserved for CONSOLE
Poky (Yocto Project Reference Distro) 2.5.3 swi-mdm9x28-wp /dev/ttyHSL1
swi-mdm9x28-wp login: [ 27.152294] LTC2941 6-0064: ltc2941 read_reg failed!
[ 27.156406] LTC2941 6-0064: Could not read status register
[ 27.205411] spi_master spi1: channel_config_store() failed(-14)
[ 27.210815] spi_master spi1: mt7697spi_init(): cp2130_update_ch_config() failed(-14)
[ 27.238111] spi_master spi1: channel_config_store() failed(-14)
[ 27.270961] spi_master spi1: mt7697spi_init(): cp2130_update_ch_config() failed(-14)
insmod: can't insert '/legato/systems/current/modules/mt7697q.ko': Bad address
Nov 6 11:19:08 swi-mdm9x28-wp user.info swiapp: sending QMI_AT_REG_AT_CMD_FWD_REQ_V01 message
Nov 6 11:19:08 swi-mdm9x28-wp user.info swiapp: Registered AT Commands event handler
Nov 6 11:19:08 swi-mdm9x28-wp user.info swiapp: Waiting for ctrCond
Nov 6 11:19:08 swi-mdm9x28-wp user.debug kernel: [ 23.496631] LE_KPI: end initscript /etc/rcS.d/S45init_irsc_util
Nov 6 11:19:08 swi-mdm9x28-wp user.debug kernel: [ 23.512976] LE_KPI: start initscript /etc/rcS.d/S45netmgrd
Nov 6 11:19:08 swi-mdm9x28-wp user.debug kernel: [ 23.553054] LE_KPI: end initscript /etc/rcS.d/S45netmgrd
Nov 6 11:19:08 swi-mdm9x28-wp user.debug kernel: [ 23.604193] LE_KPI: start initscript /etc/rcS.d/S50power_config
Nov 6 11:19:08 swi-mdm9x28-wp user.warn kernel: [ 23.642334] ++++ /etc/rcS.d/S50power_config -> ENABLE-FTRACE
Nov 6 11:19:08 swi-mdm9x28-wp user.debug kernel: [ 23.656320] LE_KPI: end initscript /etc/rcS.d/S50power_config
Nov 6 11:19:08 swi-mdm9x28-wp user.debug kernel: [ 23.691482] LE_KPI: start initscript /etc/rcS.d/S50start_fs-scrub-daemon
Nov 6 11:19:08 swi-mdm9x28-wp user.err netmgrd: QMUXD: WARNING qmi_qmux_if_pwr_up_init failed! rc=-6
Nov 6 11:19:08 swi-mdm9x28-wp user.info kernel: [ 23.732091] sps:BAM 0x04044000 is registered.
Nov 6 11:19:08 swi-mdm9x28-wp user.info kernel: [ 23.732372] sps:BAM 0x04044000 (va:0xd31c0000) enabled: ver:0x27, number of pipes:6
Nov 6 11:19:08 swi-mdm9x28-wp user.debug kernel: [ 23.771607] LE_KPI: end initscript /etc/rcS.d/S50start_fs-scrub-daemon
Nov 6 11:19:08 swi-mdm9x28-wp user.debug kernel: [ 23.881851] LE_KPI: start initscript /etc/rcS.d/S55bootmisc.sh
Nov 6 11:19:08 swi-mdm9x28-wp user.err fs-scrub-daemon: 1384:1384 Error: fs_scrub_read_state_and_resume:1102 No files found .. likely is first boot!
Nov 6 11:19:08 swi-mdm9x28-wp user.err fs-scrub-daemon: QMUXD: WARNING qmi_qmux_if_pwr_up_init failed! rc=-6
Nov 6 11:19:08 swi-mdm9x28-wp user.notice fs-scrub-daemon: 1384:1384 Verbose:fs_scrub_qmi_init:633 QMI init done!
Nov 6 11:19:08 swi-mdm9x28-wp user.debug kernel: [ 24.034134] LE_KPI: end initscript /etc/rcS.d/S55bootmisc.sh
Nov 6 11:19:08 swi-mdm9x28-wp user.debug kernel: [ 24.100456] LE_KPI: start initscript /etc/rcS.d/S55reset_reboot_cookie
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 24.164407] LE_KPI: end initscript /etc/rcS.d/S55reset_reboot_cookie
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 24.198307] LE_KPI: start initscript /etc/rcS.d/S70start_eMBMs_TunnelingModule_le
Nov 6 11:19:09 swi-mdm9x28-wp user.warn kernel: [ 24.213812] eMBMs Tunneling Module:start
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 24.271516] LE_KPI: end initscript /etc/rcS.d/S70start_eMBMs_TunnelingModule_le
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 24.333443] LE_KPI: start initscript /etc/rcS.d/S80start_stop_qmi_ip_multiclient
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 24.411627] LE_KPI: end initscript /etc/rcS.d/S80start_stop_qmi_ip_multiclient
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 24.461793] LE_KPI: start initscript /etc/rcS.d/S90startm2m.sh
Nov 6 11:19:09 swi-mdm9x28-wp user.err qmi_ip_multiclient: QMUXD: WARNING qmi_qmux_if_pwr_up_init failed! rc=-6
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 24.630021] LE_KPI: end initscript /etc/rcS.d/S90startm2m.sh
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 24.673119] LE_KPI: start initscript /etc/rcS.d/S94dnsmasq
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 24.749287] LE_KPI: end initscript /etc/rcS.d/S94dnsmasq
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 24.786109] LE_KPI: start initscript /etc/rcS.d/S95dropbear.wrapper
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 24.820411] LE_KPI: end initscript /etc/rcS.d/S95dropbear.wrapper
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 24.897423] LE_KPI: start initscript /etc/rcS.d/S96adbd
Nov 6 11:19:09 swi-mdm9x28-wp authpriv.warn dropbear[1537]: Failed loading /etc/dropbear/dropbear_dss_host_key
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 24.968144] LE_KPI: end initscript /etc/rcS.d/S96adbd
Nov 6 11:19:09 swi-mdm9x28-wp authpriv.warn dropbear[1537]: Failed loading /etc/dropbear/dropbear_ecdsa_host_key
Nov 6 11:19:09 swi-mdm9x28-wp authpriv.info dropbear[1547]: Running in background
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 25.006195] LE_KPI: start initscript /etc/rcS.d/S97data-init
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 25.031479] LE_KPI: end initscript /etc/rcS.d/S97data-init
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 25.060946] LE_KPI: start initscript /etc/rcS.d/S97port_bridge
Nov 6 11:19:09 swi-mdm9x28-wp user.warn kernel: [ 25.074342] Starting port_bridge: done
Nov 6 11:19:09 swi-mdm9x28-wp user.debug kernel: [ 25.127312] LE_KPI: end initscript /etc/rcS.d/S97port_bridge
Nov 6 11:19:10 swi-mdm9x28-wp user.debug kernel: [ 25.172539] LE_KPI: start initscript /etc/rcS.d/S98start_QCMAP_ConnectionManager_le
Nov 6 11:19:10 swi-mdm9x28-wp user.warn kernel: [ 25.183436] Starting QCMAP_ConnectionManager: QCMAP:start
Nov 6 11:19:10 swi-mdm9x28-wp user.warn kernel: [ 25.215886] done
Nov 6 11:19:10 swi-mdm9x28-wp user.debug kernel: [ 25.247501] LE_KPI: end initscript /etc/rcS.d/S98start_QCMAP_ConnectionManager_le
Nov 6 11:19:10 swi-mdm9x28-wp user.debug kernel: [ 25.311899] LE_KPI: start initscript /etc/rcS.d/S99enable_autosleep.sh
Nov 6 11:19:10 swi-mdm9x28-wp user.debug kernel: [ 25.354052] LE_KPI: end initscript /etc/rcS.d/S99enable_autosleep.sh
Nov 6 11:19:10 swi-mdm9x28-wp user.warn kernel: [ 25.394170] QCMAP:Start Main
Nov 6 11:19:10 swi-mdm9x28-wp user.debug kernel: [ 25.396440] LE_KPI: start initscript /etc/rcS.d/S99start_qti_le
Nov 6 11:19:10 swi-mdm9x28-wp user.warn kernel: [ 25.414846] Starting qti: QTI:start
Nov 6 11:19:10 swi-mdm9x28-wp user.warn kernel: [ 25.472727] USB QCMAP NL IOCTL Snd GETNEIGH Succ
Nov 6 11:19:10 swi-mdm9x28-wp user.warn kernel: [ 25.485942] done
Nov 6 11:19:10 swi-mdm9x28-wp user.debug kernel: [ 25.521518] LE_KPI: end initscript /etc/rcS.d/S99start_qti_le
Nov 6 10:19:10 swi-mdm9x28-wp daemon.info : starting pid 1617, tty '': '/usr/sbin/run_getty.sh'
Nov 6 11:19:10 swi-mdm9x28-wp user.warn kernel: [ 25.656086] QCMAP:Start DHCP server
Nov 6 11:19:10 swi-mdm9x28-wp user.warn kernel: [ 25.672539] QCMAP:DHCP server started
Nov 6 11:19:10 swi-mdm9x28-wp user.notice root: run_getty.sh: ttyHSL1 reserved for CONSOLE
Nov 6 11:19:10 swi-mdm9x28-wp daemon.info dnsmasq[825]: read /etc/hosts - 6 addresses
Nov 6 11:19:10 swi-mdm9x28-wp user.warn kernel: [ 25.913437] QCMAP:Init Complete
Nov 6 11:19:11 swi-mdm9x28-wp user.debug kernel: [ 26.581037] mangoh red mangoh red: mapping eeprom
Nov 6 11:19:11 swi-mdm9x28-wp user.info kernel: [ 26.581469] at24 4-0051: 4096 byte at24 EEPROM, read-only, 0 bytes/write
Nov 6 11:19:11 swi-mdm9x28-wp user.info kernel: [ 26.582619] sps:BAM 0x07884000 (va:0xd09c0000) enabled: ver:0x18, number of pipes:24
Nov 6 11:19:11 swi-mdm9x28-wp user.info kernel: [ 27.016610] Detected mangOH Red board revision: dv5
Nov 6 11:19:11 swi-mdm9x28-wp user.debug kernel: [ 27.016689] mangoh red mangoh red: mapping i2c switch
Nov 6 11:19:11 swi-mdm9x28-wp user.debug kernel: [ 27.017117] pca954x 4-0071: GPIO lookup for consumer reset
Nov 6 11:19:11 swi-mdm9x28-wp user.debug kernel: [ 27.017137] pca954x 4-0071: using lookup tables for GPIO lookup
Nov 6 11:19:11 swi-mdm9x28-wp user.debug kernel: [ 27.017155] pca954x 4-0071: lookup for GPIO reset failed
Nov 6 11:19:11 swi-mdm9x28-wp user.info kernel: [ 27.018207] i2c i2c-4: Added multiplexed i2c bus 5
Nov 6 11:19:11 swi-mdm9x28-wp user.info kernel: [ 27.018985] i2c i2c-4: Added multiplexed i2c bus 6
Nov 6 11:19:11 swi-mdm9x28-wp user.info kernel: [ 27.019638] i2c i2c-4: Added multiplexed i2c bus 7
Nov 6 11:19:11 swi-mdm9x28-wp user.info kernel: [ 27.021264] i2c i2c-4: Added multiplexed i2c bus 8
Nov 6 11:19:11 swi-mdm9x28-wp user.info kernel: [ 27.021288] pca954x 4-0071: registered 4 multiplexed busses for I2C switch pca9546
Nov 6 11:19:11 swi-mdm9x28-wp user.debug kernel: [ 27.021324] mangoh red mangoh red: mapping gpio expander
Nov 6 11:19:11 swi-mdm9x28-wp user.debug kernel: [ 27.031398] gpiochip_find_base: found new base at 804
Nov 6 11:19:11 swi-mdm9x28-wp user.info kernel: [ 27.031751] gpiochip_export_v2: Export gpiochip sx1509q [804,16] to v2
Nov 6 11:19:11 swi-mdm9x28-wp u�GPIOs 804 to 819 on device: sx1509q
Nov 6 11:19:11 swi-mdm9x28-wp user.debug kernel: [ 27.036060] mangoh red mangoh red: mapping accelerometer
Nov 6 11:19:11 swi-mdm9x28-wp user.debug kernel: [ 27.128657] mangoh red mangoh red: mapping bmp280 pressure sensor
Nov 6 11:19:11 swi-mdm9x28-wp user.warn kernel: [ 27.129126] 4-0076 supply vddd not found, using dummy regulator
Nov 6 11:19:11 swi-mdm9x28-wp user.warn kernel: [ 27.129190] 4-0076 supply vdda not found, using dummy regulator
Nov 6 11:19:11 swi-mdm9x28-wp user.debug kernel: [ 27.131261] bmp280 4-0076: GPIO lookup for consumer reset
Nov 6 11:19:11 swi-mdm9x28-wp user.debug kernel: [ 27.131274] bmp280 4-0076: using lookup tables for GPIO lookup
Nov 6 11:19:11 swi-mdm9x28-wp user.d[ 28.498684] gbam_disconnect_work: gbam_disconnect_work: Bam channel is not opened
ebug kernel: [ 27.131288] bmp280 4-0076: lookup for GPIO reset failed
Nov 6 11:19:11 swi-mdm9x28-wp user.debug kernel: [ 2[ 28.519199] [RMNET:HI] rmnet_config_notify_cb(): Kernel is trying to unregister ecm0
7.134169] mangoh red mangoh red: mapping bq24296 driver
Nov 6 11:19:11 swi-mdm9x28-wp user.debug kernel: [ 27.151305] mangoh red mangoh red: mapping ltc2942 battery gauge
Nov 6 11:19:11 swi-mdm9x28-wp user.err kernel: [ 27.152294] LTC2941 6-0064: ltc2941 read_reg failed!
Nov 6 11:19:11 swi-mdm9x28-wp user.err kernel: [ 27.156406] LTC2941 6-0064: Could not read status register
Nov 6 11:19:12 swi-mdm9x28-wp user.warn kernel: [ 27.162517] LTC2941: probe of 6-0064 failed with error -107
Nov 6 [ 28.570301] [RMNET:HI] rmnet_config_notify_cb(): Kernel is trying to unregister ecm0
11:19:12 swi-mdm9x28-wp user.warn kernel: [ 27.163839] insmod (1149) used greatest stack depth: 936 bytes left
Nov 6 11:19:12 swi-mdm9x28-wp user.info kernel: [ 27.177235] mt7697q mt7697spi_init(): 'mt7697q' initialize
Nov 6 11:19:12 swi-mdm9x28-wp user.err kernel: [ 27.205411] spi_master spi1: channel_config_store() failed(-14)
Nov 6 11:19:12 swi-mdm9x28-wp user.err kernel: [ 27.210815] spi_master spi1: mt7697spi_init(): cp2130_update_ch_config() failed(-14)
Nov 6 11:19:12 swi-mdm9x28-wp user.info kernel: [ 27.223130] mt7697q mt7697spi_init(): 'mt7697q' initialize
Nov 6 11:19:12 swi-mdm9x28-wp user.err kernel: [ 27.238111] spi_master spi1: channel_config_store() failed(-14)
Nov 6 11:19:12 swi-mdm9x28-wp user.crit Legato: *CRT* | supervisor[1058]/supervisor T=main | kernelModules.c ExecuteCommand() 295 | /sbin/insmod /legato/systems/current/modules/mt7697q.ko exited with error code 14.
Nov 6 11:19:12 swi-mdm9x28-wp user.err Legato: =ERR= | supervisor[1058]/supervisor T=main | kernelModules.c installModules() 1276 | Error in installing module mt7697q.ko. Restarting system ...
Nov 6 11:19:12 swi-mdm9x28-wp user.emerg Legato: *EMR* | supervisor[1058]/supervisor T=main | supervisor.c framework_Reboot() 811 | Supervisor going down to trigger reboot.
Nov 6 11:19:12 swi-mdm9x28-wp user.err kernel: [ 27.270961] spi_master spi1: mt7697spi_init(): cp2130_update_ch_config() failed(-14)
rcK: Executing run_K_scripts...
Stopping linkmon: no linkmon found; none killed
done
no port_bridge found; none killed
Stopping qmi_ip: no qmi_ip_multiclient found; none killed
Stopping eMBMs_TunnelingModule: no eMBMs_TunnelingModule found; none killed
Stopping netmgrd: stopped netmgrd (pid 1350)
done
Stopping qmuxd: stopped qmuxd (pid 1284)
done
no QCMAP_ConnectionManager found; none killed
Stopping fs-scrub-daemon: no fs-scrub-daemon found; none killed
Stopping thermal-engine: stopped thermal-engine (pid 1297)
done
stopped qti (pid 1607)
Stopping reboot daemon: stopped reboot-daemon (pid 1231)
done
Legato shutdown sequence
Service Directory still running. Killing it now ...
DONE.
umount: can't unmount /legato: Device or resource busy
Finished Legato stop Sequence
stopping time daemon
Stopping time_services: stopped time_daemon (pid 797)
done
stopping ntpd
no ntpd found; none killed
Stopping diagrebootapp: stopped diagrebootapp (pid 769)
done
stopping DNS forwarder and DHCP server: dnsmasq... stopped /usr/bin/dnsmasq (pid 825)
done.
Deconfiguring network interfaces... ifdown: interface eth0 not configured
done.
Stopping syslogd/klogd: stopped syslogd (pid 691)
stopped klogd (pid 701)
done
Stopping Dropbear SSH server: stopped /usr/sbin/dropbear (pid 1547)
dropbear.
K96mount_unionfs: RO rootfs fudge allowed.
Stopping system message bus: dbus.
K98mount_early: Executing mount_early_user_stop...
K98mount_early: RO rootfs fudge allowed.
K98mount_early: ubidetach failed for device /dev/mtd16, rcK should take care of it.
K98mount_early: Executing mount_early_legato_stop...
Can't get valid SMEM, init DSSD SMEM
Linux sub system 1
K98mount_early: Executing mount_early_userrw_stop...
K98mount_early: Executing mount_early_unset_timezone...
rcK: Executing kill_all_proc...
rcK: Executing umount_fs_generic...
rcK: Executing print_shutdown_msg...
** SYSTEM SHUTDOWN COMPLETE **
The system is going down NOW!
Sent SIGTERM to all processes
[ 31.337611] [RMNET:HI] rmnet_config_notify_cb(): Kernel is trying to unregister bridge0
[ 31.360379] [RMNET:HI] rmnet_config_notify_cb(): Kernel is trying to unregister bridge0
Sent SIGKILL to all processes
Requesting system reboot
[ 33.283971] reboot: Restarting system
[ 33.287452] Failed to disable secure wdog debug: -4
[ 33.291481] Calling SCM to disable SPMI PMI@D��I�
Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.2-00096
S - IMAGE_VARIANT_STRING=LAATANAZA
S - OEM_IMAGE_VERSION_STRING=SWI9X06Y_02.35.02.00 5208b3 jenkins 2020/06/10 00:25:22
S - Boot Config, 0x000002e1
B - 1216 - PBL, Start
B - 3720 - bootable_media_detect_entry, Start
B - 5000 - bootable_media_detect_success, Start
B - 5004 - elf_loader_entry, Start
B - 8459 - auth_hash_seg_entry, Start
B - 32126 - auth_hash_seg_exit, Start
B - 83519 - elf_segs_hash_verify_entry, Start
B - 130595 - PBL, End
B - 138592 - SBL1, Start
B - 200354 - pm_device_init, Start
B - 220393 - PM_SET_VAL:Skip
D - 18391 - pm_device_init, Delta
B - 221735 - boot_config_data_table_init, Start
D - 0 - boot_config_data_table_init, Delta - (0 Bytes)
B - 230458 - CDT version:3,Platform ID:8,Major ID:1,Minor ID:0,Subtype:129
B - 237351 - sbl1_ddr_set_params, Start
B - 241194 - Pre_DDR_clock_init, Start
D - 213 - Pre_DDR_clock_init, Delta
D - 0 - sbl1_ddr_set_params, Delta
B - 253882 - pm_driver_init, Start
D - 4453 - pm_driver_init, Delta
B - 260134 - cpr_init, Start
D - 122 - cpr_init, Delta
B - 264801 - cpr_cx_mx_apc_vol_update, Start
D - 91 - cpr_cx_mx_apc_vol_update, Delta
B - 279990 - clock_init, Start
D - 183 - clock_init, Delta
B - 280234 - boot_flash_init, Start
D - 39955 - boot_flash_init, Delta
B - 323208 - boot_flash_swi_ddr_init, Start
D - 29768 - boot_flash_swi_ddr_init, Delta
B - 459482 - Invalid PMIC gpio 3
B - 459543 - Invalid PMIC gpio 3
B - 459574 - Failed to configure/read HW ID minor bit 0
B - 464881 - hw_family:5, hw_type:22, hw_rev:40
B - 473268 - SSMEM init OK
B - 477081 - DEBUG OU: 0000000000000002
B - 477142 - DEBUG OU - setting: 2
B - 479185 - is_memory_dump_allowed (0) in this secure module
B - 485011 - ssmem_get: region 18 not exists
B - 489220 - cannot get SSMEM fwupdate region
B - 508465 - USB non-zero endpoint requirements: 9 in, 5 out
B - 510143 - opening partition 0:SWIFOTA
B - 512278 - error for readpage:0
B - 517585 - DWL-get: ecnt=1 code=0
B - 524691 - API change: date not generated by cwe_header_init
B - 529937 - Failed to read size: /swinv/item_files/CUST_IM_SWITCH_HIDE
B - 535976 - Failed to read size: /swinv/item_files/FOTA_PARTITION
B - 537349 - Failed to read size: /swinv/item_files/CUST_IM_CONFIG
B - 548634 - flags: u=1 e=1 obmsk=c,0
B - 558211 - ssmem_release: region 20 not exists
B - 558272 - ssmem_get: region 20 not exists
B - 563030 - Image Load, Start
D - 94763 - QSEE Image Loaded, Delta - (490996 Bytes)
D - 213 - boot_pm_post_tz_device_init, Delta
B - 662216 - sbl1_efs_handle_cookies, Start
D - 0 - sbl1_efs_handle_cookies, Delta
B - 670176 - DEVCFG ELF verification failure
B - 673745 - Image Load, Start
D - 30 - SEC Image Loaded, Delta - (0 Bytes)
B - 681431 - Image Load, Start
D - 55083 - RPM Image Loaded, Delta - (151248 Bytes)
B - 737215 - Image Load, Start
B - 739564 - Auth disabled for image 9
B - 781745 - ssmem_get: region 20 not exists
D - 44591 - APPSBL Image Loaded, Delta - (409744 Bytes)
B - 785009 - QSEE Execution, Start
D - 976 - QSEE Execution, Delta
B - 791719 - SBL1, End
D - 655475 - SBL1, Delta
S - Throughput, 8000 KB/s (1231012 Bytes, 139713 us)
S - DDR Frequency, 240 MHz
Android Bootloader - UART_DM Initialized!!!
[10] Qseecom Init Done in Appsbl version is 0x405000
[10] secure app region addr=0x87900000 size=0x280000[20] TZ App region notif returned with status:0 addr:87900000 size:2621440
[20] TZ App log region register returned with status:0 addr:8267d000 size:4096
[30] Qseecom TZ Init Done in Appsbl
[30] ERROR: No devinfo partition found
[30] Neither 'config' nor 'frp' partition found
[40] ERROR: No misc partition found
[1460] SSMEM init OK[1460] ssmem_get: region 20 not exists[1550] DEBUG: cmdline has root=
[1720] Channel alloc freed
[ 0.000000] GIC CPU mask not found - kernel will fail to boot.
[ 0.000000] GIC CPU mask not found - kernel will fail to boot.
[ 0.000000] MPM 1 irq mapping errored -517
[ 0.215791] spmi_pmic_arb 200f000.qcom,spmi: PMIC Arb Version-2 0x20010000
[ 0.231230] SWI ssmem_framework_init: SSMEM init OK
[ 0.231314] mdm9607-pinctrl 1000000.pinctrl: gpio-bit-map = 36
[ 0.232854] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
[ 0.236039] smd_channel_probe_now: allocation table not initialized
[ 0.243762] msm_thermal:msm_thermal_dev_probe Failed reading node=/soc/qcom,msm-thermal, key=qcom,online-hotplug-core. err:-517
[ 0.271869] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
[ 0.274863] msm_thermal:get_kernel_cluster_info CPU0 topology not initialized.
[ 0.275767] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 0.275785] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[ 0.276518] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 0.276535] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[ 0.276551] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[ 0.276563] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[ 0.370228] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
[ 0.372093] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
[ 0.436048] msm_bus_fabric_init_driver
[ 0.618457] sierra_gpio soc:sierra_gpio: property "compatible": length 12
[ 0.618474] sierra_gpio soc:sierra_gpio: property "alias-2": length 12
[ 0.618598] sierra_gpio soc:sierra_gpio: property "alias-4": length 12
[ 0.618658] sierra_gpio soc:sierra_gpio: property "alias-6": length 12
[ 0.618716] sierra_gpio soc:sierra_gpio: property "alias-7": length 12
[ 0.618771] sierra_gpio soc:sierra_gpio: property "alias-8": length 12
[ 0.618825] sierra_gpio soc:sierra_gpio: property "alias-13": length 12
[ 0.618880] sierra_gpio soc:sierra_gpio: property "alias-21": length 12
[ 0.618934] sierra_gpio soc:sierra_gpio: property "alias-22": length 12
[ 0.619008] sierra_gpio soc:sierra_gpio: property "alias-23": length 12
[ 0.619065] sierra_gpio soc:sierra_gpio: property "alias-24": length 12
[ 0.619119] sierra_gpio soc:sierra_gpio: property "alias-25": length 12
[ 0.619174] sierra_gpio soc:sierra_gpio: property "alias-28": length 12
[ 0.619229] sierra_gpio soc:sierra_gpio: property "alias-29": length 12
[ 0.619284] sierra_gpio soc:sierra_gpio: property "alias-30": length 12
[ 0.619338] sierra_gpio soc:sierra_gpio: property "alias-31": length 12
[ 0.619391] sierra_gpio soc:sierra_gpio: property "alias-32": length 12
[ 0.619446] sierra_gpio soc:sierra_gpio: property "alias-33": length 12
[ 0.619500] sierra_gpio soc:sierra_gpio: property "alias-35": length 12
[ 0.619553] sierra_gpio soc:sierra_gpio: property "alias-36": length 8
[ 0.619583] sierra_gpio soc:sierra_gpio: property "alias-37": length 8
[ 0.619613] sierra_gpio soc:sierra_gpio: property "alias-38": length 8
[ 0.619643] sierra_gpio soc:sierra_gpio: property "alias-40": length 8
[ 0.619673] sierra_gpio soc:sierra_gpio: property "alias-41": length 8
[ 0.619703] sierra_gpio soc:sierra_gpio: property "alias-42": length 12
[ 0.619757] sierra_gpio soc:sierra_gpio: property "alias-RI": length 12
[ 0.619823] sierra_gpio soc:sierra_gpio: property "alias-WLAN_EN": length 12
[ 0.619878] sierra_gpio soc:sierra_gpio: property "alias-WIFI_IRQ": length 12
[ 0.619933] sierra_gpio soc:sierra_gpio: property "name": length 12
[ 0.619944] sierra_gpio soc:sierra_gpio: Skipping unknown property "name"
[ 0.624116] scm_call failed with error code -4
[ 0.624135] msm_audio_protect_memory_region: SCM call failed, scm_call_ret -95 tz_resp 0
[ 0.629525] uart_tx_gpio is not available
[ 0.629546] uart_rx_gpio is not available
[ 0.629566] uart_cts_gpio is not available
[ 0.629585] uart_rfr_gpio is not available
[ 0.630418] sps: BAM device 0x07884000 is not registered yet.
[ 0.635471] uart_tx_gpio is not available
[ 0.635492] uart_rx_gpio is not available
[ 0.635511] uart_cts_gpio is not available
[ 0.635530] uart_rfr_gpio is not available
[ 1.025261] mdm9607-pinctrl 1000000.pinctrl: pin GPIO_4 already requested by 78b0000.uart; cannot claim for 78b0000.serial
[ 1.035681] mdm9607-pinctrl 1000000.pinctrl: pin-4 (78b0000.serial) status -22
[ 1.042861] mdm9607-pinctrl 1000000.pinctrl: could not request pin 4 (GPIO_4) from group gpio4 on device 1000000.pinctrl
[ 1.053793] msm_serial_hsl 78b0000.serial: Error applying setting, reverse things back
[ 1.115138] sps: BAM device 0x07984000 is not registered yet.
[ 1.201822] unable to find DT imem DLOAD mode node
[ 1.205909] unable to find DT imem EDLOAD mode node
[ 1.210901] unable to find DT imem dload-type node
[ 1.215391] Failed to disable secure wdog debug: -4
[ 1.247155] devfreq soc:qcom,cpubw: Couldn't update frequency transition information.
[ 1.255259] sdhci_msm 7864900.sdhci: sdhci_msm_pm_qos_parse_irq: error -22 reading irq cpu
[ 1.264315] coresight_event: error registering on panic -38
[ 1.274085] coresight-tmc 6025000.tmc: failed to get flush cti
[ 1.278882] coresight-tmc 6025000.tmc: failed to get reset cti
[ 1.346981] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[ 1.368510] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[ 1.390159] SWI ssmem_alloc_entry_get: ssmem region 20 not allocated
[ 1.395475] SWI ssmem_get: ssmem_get: region 20 not exists
[ 1.403508] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[ 1.417550] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[ 1.426694] calculate_residency: residency < 0 for LPM
[ 1.431011] parse_cpu_levels: idx 1 420
[ 1.434611] calculate_residency: residency < 0 for LPM
[ 1.439734] parse_cpu_levels: idx 2 500
[ 1.460139] parse_cpu_levels: idx 2 3040
[ 1.464101] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[ 1.481269] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
ima: setting up IMA subsystem...
ima: feature not supported
The proc node does not exist
mount root fs from partition (rootfs|system)
UBI device number 0, total 120 LEBs (30474240 bytes, 29.0 MiB), available 0 LEBs (0 bytes), LEB size 253952 bytes (248.0 KiB)
dm-verity key not installed, authentication disabled
Non-Secure version.
rootfs roothash set at compile time: 097ec61f7e03903d7cca1f502a900df678bbe0175704df9edfee30f2b45e4c14
rootfs: dev '/dev/ubiblock0_0' 'squashfs'
mount /dev/mapper/rt
rootfs: mounting took 0ms
rcS: Executing mount_essential_fs...
rcS: Executing simple_network...
rcS: Executing run_S_scripts...
S02mount_early: Executing mount_early_pseudo...
S02mount_early: Mounting SMACK security pseudo fs...
S02mount_early: Executing mount_early_other...
S02mount_early: Executing mount_early_create_dirs...
S02mount_early: Executing mount_early_set_timezone...
S02mount_early: Using timezone Universal...
S02mount_early: Executing yaffs2_kern_supported_init...
S02mount_early: Executing mount_early_user_start...
S02mount_early: RO rootfs fudge allowed.
S02mount_early: User is forcing userapp file system to be ubifs.
S02mount_early: Trying to mount UBIFS on /mnt/flash using [usrquota,grpquota,rw] mount options...
UBI device number 3, total 524 LEBs (133070848 bytes, 126.9 MiB), available 5 LEBs (1269760 bytes, 1.2 MiB), LEB size 253952 bytes (248.0 KiB)
[ 6.410117] SWI ssmem_alloc_entry_get: ssmem region 20 not allocated
[ 6.415436] SWI ssmem_get: ssmem_get: region 20 not exists
S02mount_early: Performing quota check on file system mounted at /mnt/flash
S02mount_early: UBIFS volume successfully mounted on /mnt/flash
S02mount_early: Executing mount_early_legato_start...
mount Legato from partition lefwkro
UBI device number 2, total 35 LEBs (8888320 bytes, 8.4 MiB), available 0 LEBs (0 bytes), LEB size 253952 bytes (248.0 KiB)
dm-verity key not installed, authentication disabled
Non-Secure version.
S02mount_early: SQUASHFS successfully mounted on /mnt/legato
S02mount_early: Executing mount_early_userrw_start...
S02mount_early: Mounting swirw file system as UBIFS
S02mount_early: Trying to mount UBIFS on /mnt/userrw using [usrquota,grpquota,rw] mount options...
UBI device number 4, total 100 LEBs (25395200 bytes, 24.2 MiB), available 2 LEBs (507904 bytes, 496.0 KiB), LEB size 253952 bytes (248.0 KiB)
S02mount_early: Performing quota check on file system mounted at /mnt/userrw
S02mount_early: UBIFS volume successfully mounted on /mnt/userrw
S02mount_early: swirw mounted to /mnt/userrw
S03confighw.sh: Kernel internal entropy pool filler is available, increasing write_wakeup_threshold to 3072
Starting system message bus: dbus.
Loading modules: S07mount_unionfs: RO rootfs fudge allowed.
S07mount_unionfs: Overlay over /etc is allowed
S07mount_unionfs: Using timezone [Etc/GMT-1].
Mounting local filesystems...
[ 9.353626] UBIFS error (pid: 587): cannot open "ubi0:usrfs", error -19mount: mounting ubi0:usrfs on /usr failed: No such device
mount modem from partition modem
MTD : Detected block device : /firmware for modem
UBI device number 1, total 128 LEBs (32505856 bytes, 31.0 MiB), available 21 LEBs (5332992 bytes, 5.0 MiB), LEB size 253952 bytes (248.0 KiB)
Initializing random number generator...
[ 11.430176] SWI ssmem_alloc_entry_get: ssmem region 20 not allocated
[ 11.435494] SWI ssmem_get: ssmem_get: region 20 not exists
Configuring network interfaces... done.
Starting syslogd/klogd: done
ifconfig: SIOCGIFFLAGS: No such device
Switching to composition sierra_dev (1199:68C0)
[ 12.936656] enable_store: android_usb: already disabled
SOFTAP_W_DUN: Y
Starting diagrebootapp: done
$Starting qcom_time:
starting time-daemon
Starting time_services: [ 13.403907] gbam_connect_work: gbam_connect_work: Bam channel is not ready
[ 13.415952] qti_ctrl_queue_notify: qti_ctrl_queue_notify: rmnet ctrl file handler cd5af300 is not open
done
start_at_cmux_le: UART1_SERVICE = AT
start_at_cmux_le: UART1 is AT service, starting DS_MUX daemon ...
Legato start sequence
restart_at_uart: Mapped UART1 for AT service
start_at_cmux_le: Done start_at_cmux_le script.
update-ld-cache: Removing stale mount [/etc/ld.so.conf]...
update-ld-cache: Removing stale mount [/etc/ld.so.cache]...
update-ld-cache: Updating ld.so.cache using [/legato/systems/current/lib]...
update-ld-cache: Updating /etc/ld.so.cache ...
[ 15.925701] i2c-msm-v2 78b8000.i2c: msm_bus_scale_register_client(mstr-id:86):0xd (ok)
update-ld-cache: Removing stale mount [/etc/ld.so.cache]...
[ 17.940888] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[ 17.973276] M-Notify: General: 7
[ 18.111091] diag: In diag_send_feature_mask_update, control channel is not open, p: 0, c0fa3d14
Finished Legato start Sequence
Starting reboot daemon: done
Starting atreset: done
Starting modem dependent daemons: Load modem done
Starting qmuxd: done
Starting thermal-engine: done
Starting irsc_util: Starting irsc tool
Failed to open file:/etc/sec_config
Absent/Invalid config,Default rules apply
Ending irsc tool
done
Starting netmgrd: done
Starting powerconfig for mdm9607: Starting fs-scrub-daemon: done
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
rm: can't remove '/var/log/wtmp': No such file or directory
Starting eMBMs_TunnelingModule: done
Starting qmi_ip: done
starting DNS forwarder and DHCP server: dnsmasq... /usr/bin/dnsmasq is already running
821
Starting Dropbear SSH server: dropbear.
run_getty.sh: ttyHSL1 reserved for CONSOLE
Poky (Yocto Project Reference Distro) 2.5.3 swi-mdm9x28-wp /dev/ttyHSL1