Cannot access MangOH Yellow wp7702

Hello,
I cannot access my wp7702 yellow board anymore (after some board flash by a collegue, with an app using low power).

ssh root@192.168.2.2
ssh: connect to host 192.168.2.2 port 22: No route to host

I have another board working, so I’ve extracted the following logs from both at boot time (below)

I think the following lines are problematic on the first one:

Jan  6 00:00:33 swi-mdm9x28-wp user.info kernel: [   30.469444] gpio_check_and_wake: wake-n_gpio26 STATE=SLEEP
[   48.260266] wait_for_irsc_completion: waiting for IPC Security Conf.

Why this SLEEP mode?
The line

wait_for_irsc_completion: waiting for IPC Security Conf.

is looping again and again at the end
I tried the recovery mode with swiflash -m wp77xx -r but this command is not working…

Any ideas?

LOGS:

1 (not working):

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.2-00095
S - IMAGE_VARIANT_STRING=LAATANAZA
S - OEM_IMAGE_VERSION_STRING=jenkins
S - Boot Config, 0x000002e1
B -      1216 - PBL, Start
B -      3720 - bootable_media_detect_entry, Start
B -      5047 - bootable_media_detect_success, Start
B -      5051 - elf_loader_entry, Start
B -      8505 - auth_hash_seg_entry,
 Start
B -     32154 - auth_hash_seg_exit, Start
B -     83536 - elf_segs_hash_verify_entry, Start
B -    130597 - PBL, End
B -    119286 - SBL1, Start
B -    168939 - pm_device_init, Start
B -    186568 - PM_SET_VAL:Skip
D -     16348 - pm_device_init, Delta
B -    187880 - boot_config_data_table_init, Start
D -         0 - boot_config_data_table_init, Delta - (0 Bytes)
B -    196633 - CDT version:3,Platform ID:8,Major ID:1,Minor ID:0,Subtype:129
B -    203526 - sbl1_ddr_set_params, Start
B -    207369 - Pre_DDR_clock_init, Start
D -       213 - Pre_DDR_clock_init, Delta
D -         0 - sbl1_ddr_set_params, Delta
B -    220057 - pm_driver_init, Start
D -      4453 - pm_driver_init, Delta
B -    226310 - cpr_init, Start
D -       122 - cpr_init, Delta
B -    231007 - cpr_cx_mx_apc_vol_update, Start
D -        91 - cpr_cx_mx_apc_vol_update, Delta
B -    246165 - clock_init, Start
D -       152 - clock_init, Delta
B -    246409 - boot_flash_init, Start
D -     40199 - boot_flash_init, Delta
B -    289628 - boot_flash_swi_ddr_init, Start
D -     29768 - boot_flash_swi_ddr_init, Delta
B -    426756 - hw_family:5, hw_type:22, hw_rev:40
B -    429897 - cannot detect SSMEM base
B -    429928 - SSMEM bad, reinit
B -    433100 - SSMEM init OK
B -    439535 - DEBUG OU: 0000000000000002
B -    439596 - DEBUG OU - setting: 2
B -    441548 - is_memory_dump_allowed (0) in this secure module
B -    462563 - USB non-zero endpoint requirements: 9 in, 5 out
B -    464881 - opening partition 0:SWIFOTA
B -    466345 - error for readpage:0
B -    471652 - DWL-get: ecnt=0 code=0

B -    486566 - Failed to read size: /swinv/item_files/CUST_IM_SWITCH_HIDE
B -    492544 - Failed to read size: /swinv/item_files/FOTA_PARTITION
B -    493734 - Failed to read size: /swinv/item_files/CUST_IM_CONFIG
B -    505629 - flags: u=1 e=1 obmsk=c,0
B -    507154 - ssmem_get: region 21 not exists
B -    516578 - ssmem_release: region 20 not exists
B -    516639 - ssmem_get: region 20 not exists
B -    522221 - Image Load, Start

D -     94153 - QSEE Image Loaded, Delta - (490996 Bytes)
D -       213 - boot_pm_post_tz_device_init, Delta
B -    620797 - sbl1_efs_handle_cookies, Start
D -         0 - sbl1_efs_handle_cookies, Delta
B -    628788 - DEVCFG ELF verification failure
B -    632326 - Image Load, Start
D -        30 - SEC Image Loaded, Delta - (0 Bytes)
B -    640012 - Image Load, Start

D -     55083 - RPM Image Loaded, Delta - (151200 Bytes)
B -    695796 - Image Load, Start
B -    698114 - Auth disabled for image 9

B -    740265 - ssmem_get: region 20 not exists
D -     44530 - APPSBL Image Loaded, Delta - (409204 Bytes)
B -    743529 - QSEE Execution, Start
D -       945 - QSEE Execution, Delta
B -    750300 - SBL1, End
D -    633271 - SBL1, Delta
S - Throughput, 8000 KB/s  (1230420 Bytes,  139498 us)
S - DDR Frequency, 240 MHz

Android Bootloader - UART_DM Initialized!!!
[10] Qseecom Init Done in Appsbl version is 0x405000
[10] secure app region addr=0x87900000 size=0x280000[20] TZ App region notif returned with status:0 addr:87900000 size:2621440
[20] TZ App log region register returned with status:0 addr:8267d000 size:4096
[30] Qseecom TZ Init Done in Appsbl
[30] ERROR: No devinfo partition found
[30] Neither 'config' nor 'frp' partition found
[40] ERROR: No misc partition found

[1370] SSMEM init OK[1370] ssmem_get: region 20 not exists[1450] DEBUG: cmdline has root=

[1620] Channel alloc freed

[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] MPM 1 irq mapping errored -517
[    0.215394] spmi_pmic_arb 200f000.qcom,spmi: PMIC Arb Version-2 0x20010000
[    0.230752] SWI ssmem_framework_init: SSMEM init OK
[    0.230834] mdm9607-pinctrl 1000000.pinctrl: gpio-bit-map = 36
[    0.232376] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
[    0.235553] smd_channel_probe_now: all
ocation table not initialized
[    0.243380] msm_thermal:msm_thermal_dev_probe Failed reading node=/soc/qcom,msm-thermal, key=qcom,online-hotplug-core. err:-517
[    0.271278] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
[    0.274311] msm_thermal:get_kernel_cluster_info CPU0 topology not initialized.
[    0.275241] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[    0.275258] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[    0.275993] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[    0.276010] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[    0.276025] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[    0.276038] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[    0.370233] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
[    0.372110] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
[    0.372399] i2c-msm-v2 78b8000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x3a MSTR_STS:0x0c1300c8 OPER:0x00000090
[    0.372460] i2c-msm-v2 78b8000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x3a MSTR_STS:0x0c1300c8 OPER:0x00000090
[    0.444961] msm_bus_fabric_init_driver
[    0.631432] sierra_gpio soc:sierra_gpio: property "compatible": length 12
[    0.631447] sierra_gpio soc:sierra_gpio: property "alias-2": length 12
[    0.631576] sierra_gpio soc:sierra_gpio: property "alias-4": length 12
[    0.631640] sierra_gpio soc:sierra_gpio: property "alias-6": length 12
[    0.631695] sierra_gpio soc:sierra_gpio: property "alias-7": length 12
[    0.631771] sierra_gpio soc:sierra_gpio: property "alias-8": length 12
[    0.631829] sierra_gpio soc:sierra_gpio: property "alias-13": length 12
[    0.631886] sierra_gpio soc:sierra_gpio: property "alias-21": length 12
[    0.631942] sierra_gpio soc:sierra_gpio: property "alias-22": length 12
[    0.631995] sierra_gpio soc:sierra_gpio: property "alias-23": length 12
[    0.632048] sierra_gpio soc:sierra_gpio: property "alias-24": length 12
[    0.632103] sierra_gpio soc:sierra_gpio: property "alias-25": length 12
[    0.632155] sierra_gpio soc:sierra_gpio: property "alias-28": length 12
[    0.632209] sierra_gpio soc:sierra_gpio: property "alias-29": length 12
[    0.632263] sierra_gpio soc:sierra_gpio: property "alias-30": length 12
[    0.632316] sierra_gpio soc:sierra_gpio: property "alias-31": length 12
[    0.632369] sierra_gpio soc:sierra_gpio: property "alias-32": length 12
[    0.632424] sierra_gpio soc:sierra_gpio: property "alias-33": length 12
[    0.632479] sierra_gpio soc:sierra_gpio: property "alias-35": length 12
[    0.632534] sierra_gpio soc:sierra_gpio: property "alias-36": length 8
[    0.632565] sierra_gpio soc:sierra_gpio: property "alias-37": length 8
[    0.632595] sierra_gpio soc:sierra_gpio: property "alias-38": length 8
[    0.632624] sierra_gpio soc:sierra_gpio: property "alias-40": length 8
[    0.632654] sierra_gpio soc:sierra_gpio: property "alias-41": length 8
[    0.632683] sierra_gpio soc:sierra_gpio: property "alias-42": length 12
[    0.632739] sierra_gpio soc:sierra_gpio: property "alias-RI": length 12
[    0.632804] sierra_gpio soc:sierra_gpio: property "alias-WLAN_EN": length 12
[    0.632859] sierra_gpio soc:sierra_gpio: property "alias-WIFI_IRQ": length 12
[    0.632915] sierra_gpio soc:sierra_gpio: property "name": length 12
[    0.632926] sierra_gpio soc:sierra_gpio: Skipping unknown property "name"
[    0.637165] scm_call failed with error code -4
[    0.637183] msm_audio_protect_memory_region: SCM call failed, scm_call_ret -95 tz_resp 0
[    0.642762] uart_tx_gpio is not available
[    0.642783] uart_rx_gpio is not available
[    0.642803] uart_cts_gpio is not available
[    0.642822] uart_rfr_gpio is not available
[    0.643532] sps: BAM device 0x07884000 is not registered yet.
[    0.648613] uart_tx_gpio is not available
[    0.648633] uart_rx_gpio is not available
[    0.648652] uart_cts_gpio is not available
[    0.648672] uart_rfr_gpio is not available
[    1.069921] mdm9607-pinctrl 1000000.pinctrl: pin GPIO_4 already requested by 78b0000.uart; cannot claim for 78b0000.serial
[    1.080341] mdm9607-pinctrl 1000000.pinctrl: pin-4 (78b0000.serial) status -22
[    1.087478] mdm9607-pinctrl 1000000.pinctrl: could not request pin 4 (GPIO_4) from group gpio4  on device 1000000.pinctrl
[    1.098450] msm_serial_hsl 78b0000.serial: Error applying setting, reverse things back

[    1.159527] sps: BAM device 0x07984000 is not registered yet.

[    1.241932] unable to find DT imem DLOAD mode node
[    1.246025] unable to find DT imem EDLOAD mode node
[    1.251026] unable to find DT imem dload-type node
[    1.255508] Failed to disable secure wdog debug: -4

[    1.287138] devfreq soc:qcom,cpubw: Couldn't update frequency transition information.
[    1.295561] coresight_event: error registering on panic -38
[    1.302537] coresight-tmc 6025000.tmc: failed to get flush cti
[    1.307332] coresight-tmc 6025000.tmc: failed to get reset cti
[    1.372164] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[    1.393631] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[    1.432798] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[    1.456811] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[    1.465863] calculate_residency: residency < 0 for LPM
[    1.469964] parse_cpu_levels: idx 1 420
[    1.480171] calculate_residency: residency < 0 for LPM
[    1.484280] parse_cpu_levels: idx 2 500
[    1.500153] parse_cpu_levels: idx 2 3040
[    1.504089] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[    1.521555] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

ima: setting up IMA subsystem...
ima: feature not supported
The proc node does not exist
mount root fs from partition (rootfs|system)

Non-secure.
[    1.703708] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

UBI device number 0, total 120 LEBs (30474240 bytes, 29.0 MiB), available 0 LEBs (0 bytes), LEB size 253952 bytes (248.0 KiB)

[    2.102962] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

[    2.304484] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

rootfs roothash: ea02fdf28fcabe66a2f2934fd4f514d11dd8f4104fb203a5d8b19481445e844b

rootfs: dev '/dev/ubiblock0_0' 'squashfs'
mount /dev/mapper/rt
rootfs: mounting took 0ms

rcS: Executing mount_essential_fs... 
rcS: Executing simple_network... 
rcS: Executing run_S_scripts... 

S02mount_early: Executing mount_early_pseudo... 
S02mount_early: Mounting SMACK security pseudo fs...

S02mount_early: Executing mount_early_other... 
S02mount_early: Executing mount_early_create_dirs... 

S02mount_early: Executing mount_early_set_timezone... 
S02mount_early: Using timezone Universal...
S02mount_early: Executing yaffs2_kern_supported_init... 
S02mount_early: Executing mount_early_user_start... 
S02mount_early: RO rootfs fudge allowed.
S02mount_early: User is forcing userapp file system to be ubifs.
S02mount_early: Trying to mount UBIFS on /mnt/flash using [usrquota,grpquota,rw] mount options...

[    6.150108] SWI ssmem_alloc_entry_get: ssmem region 20 not allocated
[    6.155425] SWI ssmem_get: ssmem_get: region 20 not exists

UBI device number 3, total 524 LEBs (133070848 bytes, 126.9 MiB), available 5 LEBs (1269760 bytes, 1.2 MiB), LEB size 253952 bytes (248.0 KiB)

S02mount_early: Performing quota check on file system mounted at /mnt/flash

S02mount_early: UBIFS volume successfully mounted on /mnt/flash
S02mount_early: Executing mount_early_legato_start... 
mount Legato from partition lefwkro

S02mount_early: Non-secure.

UBI device number 2, total 35 LEBs (8888320 bytes, 8.4 MiB), available 0 LEBs (0 bytes), LEB size 253952 bytes (248.0 KiB)

S02mount_early: SQUASHFS successfully mounted on /mnt/legato
S02mount_early: Executing mount_early_userrw_start... 
S02mount_early: Mounting swirw file system as UBIFS
S02mount_early: Trying to mount UBIFS on /mnt/userrw using [usrquota,grpquota,rw] mount options...

UBI device number 4, total 100 LEBs (25395200 bytes, 24.2 MiB), available 2 LEBs (507904 bytes, 496.0 KiB), LEB size 253952 bytes (248.0 KiB)

S02mount_early: Performing quota check on file system mounted at /mnt/userrw
S02mount_early: UBIFS volume successfully mounted on /mnt/userrw
S02mount_early: swirw mounted to /mnt/userrw

S03confighw.sh: Kernel internal entropy pool filler is available, increasing write_wakeup_threshold to 3072

Starting system message bus: dbus.
Loading modules: ftdi_sio 
[    8.980780] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

[    9.000042] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

S07mount_unionfs: RO rootfs fudge allowed.
S07mount_unionfs: Overlay over /etc is allowed

S07mount_unionfs: Using timezone [Universal].
Mounting local filesystems...

[    9.619165] UBIFS error (pid: 562): cannot open "ubi0:usrfs", error -19mount: mounting ubi0:usrfs on /usr failed: No such device
mount modem from partition modem

MTD : Detected block device : /firmware for modem

UBI device number 1, total 128 LEBs (32505856 bytes, 31.0 MiB), available 20 LEBs (5079040 bytes, 4.8 MiB), LEB size 253952 bytes (248.0 KiB)

Initializing random number generator...

Switching to composition sierra_dev (1199:68C0)

[   12.226512] enable_store: android_usb: already disabled

SOFTAP_W_DUN: Y
Configuring network interfaces... 
[   12.822833] gbam_connect_work: gbam_connect_work: Bam channel is not ready
[   12.833685] qti_ctrl_queue_notify: qti_ctrl_queue_notify: rmnet ctrl file handler cd66d000 is not open

done.
Starting syslogd/klogd: 
done
Starting bluetooth: ifconfig: SIOCGIFFLAGS: No such device

bluetoothd.

Starting diagrebootapp: done
$Starting qcom_time:
starting time-daemon
Starting time_services: 
done

restart_at_uart: Mapped UART1 for AT service
start_at_cmux_le: Starting DS_MUX: 

Legato start sequence
start_at_cmux_le: Done start_at_cmux_le script.

update-ld-cache: Removing stale mount [/etc/ld.so.conf]...

update-ld-cache: Removing stale mount [/etc/ld.so.cache]...

update-ld-cache: Updating ld.so.cache using [/legato/systems/current/lib]...
update-ld-cache: Updating /etc/ld.
so.cache ...

[   15.838707] i2c-msm-v2 78b8000.i2c: msm_bus_scale_register_client(mstr-id:86):0xc (ok)

[   15.897458] i2c-msm-v2 78b8000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x3a MSTR_STS:0x001363c8 OPER:0x00000090
[   15.912315] i2c-msm-v2 78b8000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x3a MSTR_STS:0x001363c8 OPER:0x00000090

update-ld-cache: Removing stale mount [/etc/ld.so.cache]...

[   18.138882] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

[   18.173077] M-Notify: General: 7
[   18.280836] diag: In diag_send_feature_mask_update, control channel is not open, p: 0, c0fb8a94

Jan  6 00:00:33 swi-mdm9x28-wp user.info kernel: [   30.458806] gpio_check_and_wake: wake-n_gpio26 STATE=WAKEUP
Jan  6 00:00:33 swi-mdm9x28-wp user.info kernel: [   30.469398] swimcu_calibrate_event_handle: MCU calibrate completed with remaining time 0
Jan  6 00:00:33 swi-mdm9x28-wp user.info kernel: [   30.469424] swimcu_lpo_calibrate_calc: MCU time=30000 vs MDM time=30032 
Jan  6 00:00:33 swi-mdm9x28-wp user.info kernel: [   30.469444] gpio_check_and_wake: wake-n_gpio26 STATE=SLEEP

[   48.260266] wait_for_irsc_completion: waiting for IPC Security Conf.

[   48.790213] wait_for_irsc_completion: waiting for IPC Security Conf.

Jan  6 00:00:51 swi-mdm9x28-wp user.err kernel: [   48.260266] wait_for_irsc_completion: waiting for IPC Security Conf.
Jan  6 00:00:51 swi-mdm9x28-wp user.err kernel: [   48.790213] wait_for_irsc_completion: waiting for IPC Security Conf.

[   49.150206] wait_for_irsc_completion: waiting for IPC Security Conf.

[   49.890191] wait_for_irsc_completion: waiting for IPC Security Conf.

...
...

Logs 2:

Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.2-00095
S - IMAGE_VARIANT_STRING=LAATANAZA
S - OEM_IMAGE_VERSION_STRING=jenkins
S - Boot Config, 0x000002e1
B -      1216 - PBL, Start
B -      3720 - bootable_media_detect_entry, Start
B -      5037 - bootable_media_detect_success, Start
B -      5041 - elf_loader_entry, Start
B -      8496 - auth_hash_seg_entry,
 Start
B -     32150 - auth_hash_seg_exit, Start
B -     83537 - elf_segs_hash_verify_entry, Start
B -    130603 - PBL, End
B -    114954 - SBL1, Start
B -    162778 - pm_device_init, Start
B -    179858 - PM_SET_VAL:Skip
D -     15890 - pm_device_init, Delta
B -    181200 - boot_config_data_table_init, Start
D -         0 - boot_config_data_table_init, Delta - (0 Bytes)
B -    189923 - CDT version:3,Platform ID:8,Major ID:1,Minor ID:0,Subtype:129
B -    196816 - sbl1_ddr_set_params, Start
B -    200659 - Pre_DDR_clock_init, Start
D -       213 - Pre_DDR_clock_init, Delta
D -         0 - sbl1_ddr_set_params, Delta
B -    213347 - pm_driver_init, Start
D -      4453 - pm_driver_init, Delta
B -    219600 - cpr_init, Start
D -       122 - cpr_init, Delta
B -    224266 - cpr_cx_mx_apc_vol_update, Start
D -        91 - cpr_cx_mx_apc_vol_update, Delta
B -    239455 - clock_init, Start
D -       183 - clock_init, Delta
B -    239699 - boot_flash_init, Start
D -     39924 - boot_flash_init, Delta
B -    282643 - boot_flash_swi_ddr_init, Start
D -     29768 - boot_flash_swi_ddr_init, Delta
B -    402295 - hw_family:5, hw_type:22, hw_rev:40
B -    405345 - cannot detect SSMEM base
B -    405406 - SSMEM bad, reinit
B -    408669 - SSMEM init OK
B -    424529 - USB non-zero endpoint requirements: 9 in, 5 out
B -    426817 - opening partition 0:SWIFOTA
B -    428372 - error for readpage:0
B -    433588 - DWL-get: ecnt=0 code=0
B -    448350 - Failed to read size: /swinv/item_files/CUST_IM_SWITCH_HIDE
B -    453657 - Failed to read size: /swinv/item_files/FOTA_PARTITION
B -    455029 - Failed to read size: /swinv/item_files/CUST_IM_CONFIG
B -    466955 - flags: u=1 e=1 obmsk=c,0
B -    468632 - ssmem_get: region 21 not exists
B -    476257 - ssmem_release: region 20 not exists
B -    476318 - ssmem_get: region 20 not exists
B -    482083 - Image Load, Start

D -     94123 - QSEE Image Loaded, Delta - (490996 Bytes)
D -       213 - boot_pm_post_tz_device_init, Delta
B -    580598 - sbl1_efs_handle_cookies, Start
D -         0 - sbl1_efs_handle_cookies, Delta
B -    588589 - DEVCFG ELF verification failure
B -    592127 - Image Load, Start
D -         0 - SEC Image Loaded, Delta - (0 Bytes)
B -    599813 - Image Load, Start

D -     55174 - RPM Image Loaded, Delta - (151200 Bytes)
B -    655689 - Image Load, Start
B -    658007 - Auth disabled for image 9

B -    700158 - ssmem_get: region 20 not exists
D -     44530 - APPSBL Image Loaded, Delta - (409204 Bytes)
B -    703421 - QSEE Execution, Start
D -       762 - QSEE Execution, Delta
B -    710192 - SBL1, End
D -    597495 - SBL1, Delta
S - Throughput, 8000 KB/s  (1230420 Bytes,  139437 us)
S - DDR Frequency, 240 MHz

Android Bootloader - UART_DM Initialized!!!
[10] Qseecom Init Done in Appsbl version is 0x405000
[10] secure app region addr=0x87900000 size=0x280000[20] TZ App region notif returned with status:0 addr:87900000 size:2621440
[20] TZ App log region register returned with status:0 addr:8267d000 size:4096
[30] Qseecom TZ Init Done in Appsbl
[30] ERROR: No devinfo partition found
[30] Neither 'config' nor 'frp' partition found
[40] ERROR: No misc partition found

[1370] SSMEM init OK[1370] ssmem_get: region 20 not exists[1450] DEBUG: cmdline has root=

[1620] Channel alloc freed

[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] MPM 1 irq mapping errored -517
[    0.215320] spmi_pmic_arb 200f000.qcom,spmi: PMIC Arb Version-2 0x20010000
[    0.230722] SWI ssmem_framework_init: SSMEM init OK
[    0.230808] mdm9607-pinctrl 1000000.pinctrl: gpio-bit-map = 36
[    0.232350] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
[    0.235515] smd_channel_probe_now: a
llocation table not initialized
[    0.243336] msm_thermal:msm_thermal_dev_probe Failed reading node=/soc/qcom,msm-thermal, key=qcom,online-hotplug-core. err:-517
[    0.271193] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
[    0.274229] msm_thermal:get_kernel_cluster_info CPU0 topology not initialized.
[    0.275163] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[    0.275180] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[    0.275909] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[    0.275927] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[    0.275942] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[    0.275955] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[    0.370237] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
[    0.372109] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
[    0.372398] i2c-msm-v2 78b8000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x3a MSTR_STS:0x081343c8 OPER:0x00000090
[    0.372455] i2c-msm-v2 78b8000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x3a MSTR_STS:0x081343c8 OPER:0x00000090
[    0.444924] msm_bus_fabric_init_driver
[    0.631313] sierra_gpio soc:sierra_gpio: property "compatible": length 12
[    0.631329] sierra_gpio soc:sierra_gpio: property "alias-2": length 12
[    0.631457] sierra_gpio soc:sierra_gpio: property "alias-4": length 12
[    0.631519] sierra_gpio soc:sierra_gpio: property "alias-6": length 12
[    0.631575] sierra_gpio soc:sierra_gpio: property "alias-7": length 12
[    0.631650] sierra_gpio soc:sierra_gpio: property "alias-8": length 12
[    0.631707] sierra_gpio soc:sierra_gpio: property "alias-13": length 12
[    0.631761] sierra_gpio soc:sierra_gpio: property "alias-21": length 12
[    0.631815] sierra_gpio soc:sierra_gpio: property "alias-22": length 12
[    0.631869] sierra_gpio soc:sierra_gpio: property "alias-23": length 12
[    0.631922] sierra_gpio soc:sierra_gpio: property "alias-24": length 12
[    0.631975] sierra_gpio soc:sierra_gpio: property "alias-25": length 12
[    0.632030] sierra_gpio soc:sierra_gpio: property "alias-28": length 12
[    0.632084] sierra_gpio soc:sierra_gpio: property "alias-29": length 12
[    0.632139] sierra_gpio soc:sierra_gpio: property "alias-30": length 12
[    0.632192] sierra_gpio soc:sierra_gpio: property "alias-31": length 12
[    0.632246] sierra_gpio soc:sierra_gpio: property "alias-32": length 12
[    0.632300] sierra_gpio soc:sierra_gpio: property "alias-33": length 12
[    0.632355] sierra_gpio soc:sierra_gpio: property "alias-35": length 12
[    0.632409] sierra_gpio soc:sierra_gpio: property "alias-36": length 8
[    0.632440] sierra_gpio soc:sierra_gpio: property "alias-37": length 8
[    0.632470] sierra_gpio soc:sierra_gpio: property "alias-38": length 8
[    0.632500] sierra_gpio soc:sierra_gpio: property "alias-40": length 8
[    0.632529] sierra_gpio soc:sierra_gpio: property "alias-41": length 8
[    0.632559] sierra_gpio soc:sierra_gpio: property "alias-42": length 12
[    0.632615] sierra_gpio soc:sierra_gpio: property "alias-RI": length 12
[    0.632683] sierra_gpio soc:sierra_gpio: property "alias-WLAN_EN": length 12
[    0.632740] sierra_gpio soc:sierra_gpio: property "alias-WIFI_IRQ": length 12
[    0.632796] sierra_gpio soc:sierra_gpio: property "name": length 12
[    0.632807] sierra_gpio soc:sierra_gpio: Skipping unknown property "name"
[    0.637033] scm_call failed with error code -4
[    0.637053] msm_audio_protect_memory_region: SCM call failed, scm_call_ret -95 tz_resp 0
[    0.642635] uart_tx_gpio is not available
[    0.642656] uart_rx_gpio is not available
[    0.642675] uart_cts_gpio is not available
[    0.642695] uart_rfr_gpio is not available
[    0.643400] sps: BAM device 0x07884000 is not registered yet.
[    0.648457] uart_tx_gpio is not available
[    0.648477] uart_rx_gpio is not available
[    0.648496] uart_cts_gpio is not available
[    0.648515] uart_rfr_gpio is not available
[    1.069844] mdm9607-pinctrl 1000000.pinctrl: pin GPIO_4 already requested by 78b0000.uart; cannot claim for 78b0000.serial
[    1.080266] mdm9607-pinctrl 1000000.pinctrl: pin-4 (78b0000.serial) status -22
[    1.087403] mdm9607-pinctrl 1000000.pinctrl: could not request pin 4 (GPIO_4) from group gpio4  on device 1000000.pinctrl
[    1.098375] msm_serial_hsl 78b0000.serial: Error applying setting, reverse things back

[    1.159387] sps: BAM device 0x07984000 is not registered yet.

[    1.241942] unable to find DT imem DLOAD mode node
[    1.246029] unable to find DT imem EDLOAD mode node
[    1.251021] unable to find DT imem dload-type node
[    1.255518] Failed to disable secure wdog debug: -4

[    1.287141] devfreq soc:qcom,cpubw: Couldn't update frequency transition information.
[    1.295562] coresight_event: error registering on panic -38
[    1.302547] coresight-tmc 6025000.tmc: failed to get flush cti
[    1.307343] coresight-tmc 6025000.tmc: failed to get reset cti
[    1.372220] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[    1.393663] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

[    1.432792] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[    1.448153] calculate_residency: residency < 0 for LPM
[    1.460578] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[    1.467864] parse_cpu_levels: idx 1 420
[    1.480163] calculate_residency: residency < 0 for LPM
[    1.484272] parse_cpu_levels: idx 2 500
[    1.490340] parse_cpu_levels: idx 2 3040
[    1.494238] mdm9607-asoc-snd soc:sound-wm8944: Defer
ing mdm_asoc_machine_probe, q6_state 0
[    1.513937] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

ima: setting up IMA subsystem...
ima: feature not supported
The proc node does not exist
mount root fs from partition (rootfs|system)

Non-secure.
[    1.703695] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

UBI device number 0, total 120 LEBs (30474240 bytes, 29.0 MiB), available 0 LEBs (0 bytes), LEB size 253952 bytes (248.0 KiB)

[    2.102950] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

[    2.304460] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

rootfs roothash: b029191edf2040c2267b1fac071248696940b4c52f7a5dcc2e7e6a228312694a

rootfs: dev '/dev/ubiblock0_0' 'squashfs'
mount /dev/mapper/rt
rootfs: mounting took 0ms

rcS: Executing mount_essential_fs... 
rcS: Executing simple_network... 
rcS: Executing run_S_scripts... 

S02mount_early: Executing mount_early_pseudo... 
S02mount_early: Mounting SMACK security pseudo fs...

S02mount_early: Executing mount_early_other... 
S02mount_early: Executing mount_early_create_dirs... 

S02mount_early: Executing mount_early_set_timezone... 
S02mount_early: Using timezone Universal...
S02mount_early: Executing yaffs2_kern_supported_init... 
S02mount_early: Executing mount_early_user_start... 
S02mount_early: RO rootfs fudge allowed.
S02mount_early: User is forcing userapp file system to be ubifs.
S02mount_early: Trying to mount UBIFS on /mnt/flash using [usrquota,grpquota,rw] mount options...

[    6.150108] SWI ssmem_alloc_entry_get: ssmem region 20 not allocated
[    6.155425] SWI ssmem_get: ssmem_get: region 20 not exists

UBI device number 3, total 524 LEBs (133070848 bytes, 126.9 MiB), available 5 LEBs (1269760 bytes, 1.2 MiB), LEB size 253952 bytes (248.0 KiB)

S02mount_early: Performing quota check on file system mounted at /mnt/flash
S02mount_earl
y: UBIFS volume successfully mounted on /mnt/flash
S02mount_early: Executing mount_early_legato_start... 
mount Legato from partition lefwkro

S02mount_early: Non-secure.

UBI device number 2, total 35 LEBs (8888320 bytes, 8.4 MiB), available 0 LEBs (0 bytes), LEB size 253952 bytes (248.0 KiB)

S02mount_early: SQUASHFS successfully mounted on /mnt/legato
S02mount_early: Executing mount_early_userrw_start... 
S02mount_early: Mounting swirw file system as UBIFS
S02mount_early: Trying to mount UBIFS on /mnt/userrw using [usrquota,grpquota,rw] mount options...

UBI device number 4, total 100 LEBs (25395200 bytes, 24.2 MiB), available 2 LEBs (507904 bytes, 496.0 KiB), LEB size 253952 bytes (248.0 KiB)

S02mount_early: Performing quota check on file system mounted at /mnt/userrw
S02
mount_early: UBIFS volume successfully mounted on /mnt/userrw
S02mount_early: swirw mounted to /mnt/userrw

S03confighw.sh: Kernel internal entropy pool filler is available, increasing write_wakeup_threshold to 3072

Starting system message bus: dbus.
Loading modules: ftdi_sio 
[    9.422172] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

[    9.444767] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

S07mount_unionfs: RO rootfs fudge allowed.
S07mount_unionfs: Overlay over /etc is allowed

S07mount_unionfs: Using timezone [Universal].
Mounting local filesystems...

[   10.055655] UBIFS error (pid: 564): cannot open "ubi0:usrfs", error -19mount: mounting ubi0:usrfs on /usr failed: No such device
mount modem from partition modem
MTD : Detected b
lock device : /firmware for modem

UBI device number 1, total 128 LEBs (32505856 bytes, 31.0 MiB), available 20 LEBs (5079040 bytes, 4.8 MiB), LEB size 253952 bytes (248.0 KiB)

Initializing random number generator...

Switching to composition sierra_dev (1199:68C0)

[   12.655139] enable_store: android_usb: already disabled

SOFTAP_W_DUN: Y
Configuring network interfaces... 
[   13.274104] gbam_connect_work: gbam_connect_work: Bam channel is not ready
[   13.286605] qti_ctrl_queue_notify: qti_ctrl_queue_notify: rmnet ctrl file handler cd66d000 is not open

done.
Starting syslogd/klogd: 
done
Starting bluetooth: ifconfig: SIOCGIFFLAGS: No such device

bluetoothd.
Starting diagrebootapp: done
$Starting qcom_ti
me:
starting time-daemon
Starting time_services: done

Legato start sequence

start_at_cmux_le: Starting DS_MUX: 
restart_at_uart: Mapped UART1 for AT service

start_at_cmux_le: Done start_at_cmux_le script.

update-ld-cache: Removing stale mount [/etc/ld.so.conf]...

update-ld-cache: Removing stale mount [/etc/ld.so.cache]...

update-ld-cache: Updating ld.so.cache using [/legato/systems/current/lib]...

update-ld-cache: Updating /etc/ld.so.cache ...

[   16.326825] i2c-msm-v2 78b8000.i2c: msm_bus_scale_register_client(mstr-id:86):0xc (ok)

[   16.388955] i2c-msm-v2 78b8000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x3a MSTR_STS:0x0c1343c8 OPER:0x00000090
[   16.403803] i2c-msm-v2 78b8000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x3a MSTR_STS:0x0c1343c8 OPER:0x00000090

update-ld-cache: Removing stale mount [/etc/ld.so.cache]...

[   18.587761] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

[   18.621035] M-Notify: General: 7
[   18.727863] diag: In diag_send_feature_mask_update, control channel is not open, p: 0, c0fb8a94

Finished Legato start Sequence
Starting reboot daemon: done

Starting atreset: done
Starting modem dependent daemons: Load modem done

Starting qmuxd: done
Starting thermal-engine: done
Starting irsc_util: Starting irsc tool
Failed to open file:/etc/sec_config
Absent/Invalid config,Default rules apply
Ending irsc tool
done
Starting netmgrd: done
Starting fs-scrub-daemon: done

net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1

rm: can't remove '/var/log/wtmp': No such file or directory

Starting eMBMs_TunnelingModule: done
Starting qmi_ip: done

[   24.821563] adm_callback: cmd = 0x10322 returned error = 0x16
[   24.826278] adm_callback: ADM map error, resuming
[   24.831137] adm_memory_map_regions: DSP returned error[ADSP_ERR_MAX]
[   24.837301] adm_map_cal_data: map did not work! cal_type 0 ret -68
starting DNS forwarder and DHCP server: dnsmasq... [   24.860207] map_memory: map_cal failed, cal type 10, 
ret = -19!
[   24.865157] adm_alloc_cal: cal_utils_alloc_block failed, ret = -19, cal type = 10!
[   24.884535] call_allocs: alloc failed!
done.

Starting Dropbear SSH server: 
Starting port_bridge: stopping DNS forwarder and DHCP server: dnsmasq... dropbear.
done
stopped /usr/bin/dnsmasq (pid 1275)
done.
starting DNS forwarder and DHCP server: dnsmasq... done.

run_getty.sh: ttyHSL1 reserved for CONSOLE

Poky (Yocto Project Reference Distro) 2.5.3 swi-mdm9x28-wp /dev/ttyHSL1

swi-mdm9x28-wp login: 
... 
...

can you load the clean official FW to it and see if it works?

https://source.sierrawireless.com/resources/airprime/software/wp77xx/wp77xx-firmware-release-12/#sthash.z2Kz7H5i.dpbs

swiflash -m "wp77xx" -i WP77xx_Release12_SIERRA.spk

Detecting USB of the target
DONE
Communicating with the target
DONE
Switching to firmware download mode
............DONE
Downloading the firmware
..................DONE
Rebooting the module
...........DONE
Firmware Download SUCCESS

But still the same behaviour:

ssh root@192.168.2.2
ssh: connect to host 192.168.2.2 port 22: No route to host

LOGS:

[...]

B -    979507 - Sahara over USB

B -   6468348 - Sahara: Hello pkt sent

B -  29358842 - ssmem_get: region 20 not exists
B -  29359574 - ssmem_get: region 20 not exists
B -  29362502 - ssmem_get: region 20 not exists
B -  29365827 - ssmem_get: region 20 not exists
B -  29370920 - ssmem_get: region 20 not exists

B -  40779537 - AUTH_SKIPPED=USER,STATUS=PASS

B -  417850\0x03\0x00

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.2-00095
S - IMAGE_VARIANT_STRING=LAATANAZA
S - OEM_IMAGE_VERSION_STRING=jenkins
S - Boot Config, 0x000002e1
B -      1216 - PBL, Start
B -      3720 - bootable_media_detect_entry, Start
B -      4401 - bootable_media_detect_success, Start
B -      4405 - elf_loader_entry, Start
B -      7859 - auth_hash_seg_entry,
 Start
B -     31507 - auth_hash_seg_exit, Start
B -     82893 - elf_segs_hash_verify_entry, Start
B -    129959 - PBL, End
B -    138378 - SBL1, Start
B -    196206 - pm_device_init, Start
B -    216397 - PM_SET_VAL:Skip
D -     18818 - pm_device_init, Delta
B -    218075 - boot_config_data_table_init, Start
D -        30 - boot_config_data_table_init, Delta - (0 Bytes)
B -    226462 - CDT version:3,Platform ID:8,Major ID:1,Minor ID:0,Subtype:129
B -    233355 - sbl1_ddr_set_params, Start
B -    237168 - Pre_DDR_clock_init, Start
D -       244 - Pre_DDR_clock_init, Delta
D -         0 - sbl1_ddr_set_params, Delta
B -    249886 - pm_driver_init, Start
D -      4453 - pm_driver_init, Delta
B -    256139 - cpr_init, Start
D -       122 - cpr_init, Delta
B -    260836 - cpr_cx_mx_apc_vol_update, Start
D -        91 - cpr_cx_mx_apc_vol_update, Delta
B -    275994 - clock_init, Start
D -       152 - clock_init, Delta
B -    276238 - boot_flash_init, Start
D -     39985 - boot_flash_init, Delta
B -    320951 - boot_flash_swi_ddr_init, Start
D -     29768 - boot_flash_swi_ddr_init, Delta

B -    462349 - hw_family:5, hw_type:22, hw_rev:40
B -    466223 - SSMEM init OK
B -    470096 - DEBUG OU: 0000000000000002
B -    470157 - DEBUG OU - setting: 2
B -    470950 - is_memory_dump_allowed (0) in this secure module
B -    491965 - USB non-zero endpoint requirements: 9 in, 5 out
B -    493581 - opening partition 0:SWIFOTA
B -    495777 - error for readpage:0
B -    501084 - DWL-get: ecnt=0 code=0
B -    515938 - Failed to read size: /swinv/item_files/CUST_IM_SWITCH_HIDE

B -    521946 - Failed to read size: /swinv/item_files/FOTA_PARTITION
B -    523136 - Failed to read size: /swinv/item_files/CUST_IM_CONFIG
B -    535000 - flags: u=1 e=1 obmsk=c,0
B -    545187 - ssmem_release: region 20 not exists
B -    545248 - ssmem_get: region 20 not exists
B -    550860 - Image Load, Start

D -     94123 - QSEE Image Loaded, Delta - (490996 Bytes)
D -       183 - boot_pm_post_tz_device_init, Delta
B -    649406 - sbl1_efs_handle_cookies, Start
D -         0 - sbl1_efs_handle_cookies, Delta
B -    657397 - DEVCFG ELF verification failure
B -    660874 - Image Load, Start
D -        30 - SEC Image Loaded, Delta - (0 Bytes)
B -    668651 - Image Load, Start

D -     55053 - RPM Image Loaded, Delta - (151200 Bytes)
B -    724405 - Image Load, Start
B -    726754 - Auth disabled for image 9

B -    768905 - ssmem_get: region 20 not exists
D -     44561 - APPSBL Image Loaded, Delta - (409204 Bytes)
B -    772168 - QSEE Execution, Start
D -       945 - QSEE Execution, Delta
B -    778909 - SBL1, End
D -    642818 - SBL1, Delta
S - Throughput, 8000 KB/s  (1230420 Bytes,  139745 us)
S - DDR Frequency, 240 MHz

Android Bootloader - UART_DM Initialized!!!
[10] Qseecom Init Done in Appsbl version is 0x405000
[10] secure app region addr=0x87900000 size=0x280000[20] TZ App region notif returned with status:0 addr:87900000 size:2621440
[20] TZ App log region register returned with status:0 addr:8267d000 size:4096
[30] Qseecom TZ Init Done in Appsbl
[30] ERROR: No devinfo partition found
[30] Neither 'config' nor 'frp' partition found
[40] ERROR: No misc partition found

[1370] SSMEM init OK[1370] ssmem_get: region 20 not exists[1460] DEBUG: cmdline has root=

[1630] Channel alloc freed

[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] MPM 1 irq mapping errored -517
[    0.215402] spmi_pmic_arb 200f000.qcom,spmi: PMIC Arb Version-2 0x20010000
[    0.230795] SWI ssmem_framework_init: SSMEM init OK
[    0.230878] mdm9607-pinctrl 1000000.pinctrl: gpio-bit-map = 36
[    0.232409] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
[    0.235554] smd_channel_probe_now: a
llocation table not initialized
[    0.243332] msm_thermal:msm_thermal_dev_probe Failed reading node=/soc/qcom,msm-thermal, key=qcom,online-hotplug-core. err:-517
[    0.271150] msm_mpm_dev_probe(): Cannot get clk resource for XO: -517
[    0.274158] msm_thermal:get_kernel_cluster_info CPU0 topology not initialized.
[    0.275086] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[    0.275103] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[    0.275841] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[    0.275858] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[    0.275874] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[    0.275887] msm_thermal:get_cpu_freq_plan_len Error reading CPU0 freq table len. error:-19
[    0.370050] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
[    0.372015] AXI: msm_bus_scale_register_client(): msm_bus_scale_register_client: Bus driver not ready.
[    0.372308] i2c-msm-v2 78b8000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x3a MSTR_STS:0x0c1300c8 OPER:0x00000090
[    0.372366] i2c-msm-v2 78b8000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x3a MSTR_STS:0x0c1300c8 OPER:0x00000090
[    0.421525] swimcu_lpo_calibrate_calc: bogus data MCU time=30000 vs MDM time=421 
[    0.439696] msm_bus_fabric_init_driver
[    0.626611] sierra_gpio soc:sierra_gpio: property "compatible": length 12
[    0.626626] sierra_gpio soc:sierra_gpio: property "alias-2": length 12
[    0.626756] sierra_gpio soc:sierra_gpio: property "alias-4": length 12
[    0.626818] sierra_gpio soc:sierra_gpio: property "alias-6": length 12
[    0.626876] sierra_gpio soc:sierra_gpio: property "alias-7": length 12
[    0.626933] sierra_gpio soc:sierra_gpio: property "alias-8": length 12
[    0.626989] sierra_gpio soc:sierra_gpio: property "alias-13": length 12
[    0.627044] sierra_gpio soc:sierra_gpio: property "alias-21": length 12
[    0.627097] sierra_gpio soc:sierra_gpio: property "alias-22": length 12
[    0.627151] sierra_gpio soc:sierra_gpio: property "alias-23": length 12
[    0.627205] sierra_gpio soc:sierra_gpio: property "alias-24": length 12
[    0.627259] sierra_gpio soc:sierra_gpio: property "alias-25": length 12
[    0.627313] sierra_gpio soc:sierra_gpio: property "alias-28": length 12
[    0.627367] sierra_gpio soc:sierra_gpio: property "alias-29": length 12
[    0.627421] sierra_gpio soc:sierra_gpio: property "alias-30": length 12
[    0.627475] sierra_gpio soc:sierra_gpio: property "alias-31": length 12
[    0.627530] sierra_gpio soc:sierra_gpio: property "alias-32": length 12
[    0.627583] sierra_gpio soc:sierra_gpio: property "alias-33": length 12
[    0.627638] sierra_gpio soc:sierra_gpio: property "alias-35": length 12
[    0.627692] sierra_gpio soc:sierra_gpio: property "alias-36": length 8
[    0.627722] sierra_gpio soc:sierra_gpio: property "alias-37": length 8
[    0.627753] sierra_gpio soc:sierra_gpio: property "alias-38": length 8
[    0.627782] sierra_gpio soc:sierra_gpio: property "alias-40": length 8
[    0.627811] sierra_gpio soc:sierra_gpio: property "alias-41": length 8
[    0.627840] sierra_gpio soc:sierra_gpio: property "alias-42": length 12
[    0.627896] sierra_gpio soc:sierra_gpio: property "alias-RI": length 12
[    0.627962] sierra_gpio soc:sierra_gpio: property "alias-WLAN_EN": length 12
[    0.628018] sierra_gpio soc:sierra_gpio: property "alias-WIFI_IRQ": length 12
[    0.628072] sierra_gpio soc:sierra_gpio: property "name": length 12
[    0.628083] sierra_gpio soc:sierra_gpio: Skipping unknown property "name"
[    0.632245] scm_call failed with error code -4
[    0.632265] msm_audio_protect_memory_region: SCM call failed, scm_call_ret -95 tz_resp 0
[    0.637658] uart_tx_gpio is not available
[    0.637679] uart_rx_gpio is not available
[    0.637699] uart_cts_gpio is not available
[    0.637719] uart_rfr_gpio is not available
[    0.638436] sps: BAM device 0x07884000 is not registered yet.
[    0.643514] uart_tx_gpio is not available
[    0.643535] uart_rx_gpio is not available
[    0.643554] uart_cts_gpio is not available
[    0.643574] uart_rfr_gpio is not available
[    1.072405] mdm9607-pinctrl 1000000.pinctrl: pin GPIO_4 already requested by 78b0000.uart; cannot claim for 78b0000.serial
[    1.082784] mdm9607-pinctrl 1000000.pinctrl: pin-4 (78b0000.serial) status -22
[    1.089926] mdm9607-pinctrl 1000000.pinctrl: could not request pin 4 (GPIO_4) from group gpio4  on device 1000000.pinctrl
[    1.100903] msm_serial_hsl 78b0000.serial: Error applying setting, reverse things back

[    1.161959] sps: BAM device 0x07984000 is not registered yet.

[    1.241829] unable to find DT imem DLOAD mode node
[    1.245921] unable to find DT imem EDLOAD mode node
[    1.250913] unable to find DT imem dload-type node
[    1.255408] Failed to disable secure wdog debug: -4

[    1.287043] devfreq soc:qcom,cpubw: Couldn't update frequency transition information.
[    1.295164] sdhci_msm 7864900.sdhci: sdhci_msm_pm_qos_parse_irq: error -22 reading irq cpu
[    1.304199] coresight_event: error registering on panic -38
[    1.313546] coresight-tmc 6025000.tmc: failed to get flush cti
[    1.318347] coresight-tmc 6025000.tmc: failed to get reset cti
[    1.328533] NIDnT disabled, only sd mode supported.

[    1.421735] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

[    1.453047] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

[    1.532530] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[    1.547740] calculate_residency: residency < 0 for LPM

[    1.570501] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[    1.577789] parse_cpu_levels: idx 1 420
[    1.590137] calculate_residency: residency < 0 for LPM
[    1.594245] parse_cpu_levels: idx 2 500
[    1.598060] parse_cpu_levels: idx 2 3040
[    1.631145] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0
[    1.642900] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

ima: setting up IMA subsystem...
ima: feature not supported
The proc node does not exist
mount root fs from partition (rootfs|system)

Non-secure.

UBI device number 0, total 120 LEBs (30474240 bytes, 29.0 MiB), available 0 LEBs (0 bytes), LEB size 253952 bytes (248.0 KiB)

[    6.150121] SWI ssmem_alloc_entry_get: ssmem region 20 not allocated
[    6.155438] SWI ssmem_get: ssmem_get: region 20 not exists

rootfs roothash: 021e78097bf831775d8b43a7fab88e89499b7cd601992bd9342f4d8d8763758e

[    7.352101] msm_hsic_host 7c00000.hsic_host: Unable to suspend PHY

rootfs: dev '/dev/ubiblock0_0' 'squashfs'
mount /dev/mapper/rt
rootfs: mounting took 0ms

rcS: Executing mount_essential_fs... 
rcS: Executing simple_network... 
rcS: Executing run_S_scripts... 

S02mount_early: Executing mount_early_pseudo... 
S02mount_early: Mounting SMACK security pseudo fs...

S02mount_early: Executing mount_early_other... 
S02mount_early: Executing mount_early_create_dirs... 
S02
mount_early: Executing mount_early_set_timezone... 
S02mount_early: Using timezone Universal...
S02mount_early: Executing yaffs2_kern_supported_init... 
S02mount_early: Executing mount_early_user_start... 
S02mount_early: RO rootfs fudge allowed.
S02mount_early: User is forcing userapp file system to be ubifs.
S02mount_early: Trying to mount UBIFS on /mnt/flash using [usrquota,grpquota,rw] mount options...

UBI device number 3, total 524 LEBs (133070848 bytes, 126.9 MiB), available 5 LEBs (1269760 bytes, 1.2 MiB), LEB size 253952 bytes (248.0 KiB)

S02mount_early: Performing quota check on file system mounted at /mnt/flash

S02mount_early: UBIFS volume successfully mounted on /mnt/flash
S02mount_early: Executing mount_early_legato_start... 
mount Legato from partition lefwkro

S02mount_early: Non-secure.

UBI device number 2, total 35 LEBs (8888320 bytes, 8.4 MiB), available 0 LEBs (0 bytes), LEB size 253952 bytes (248.0 KiB)

S02mount_early: SQUASHFS successfully mounted on /mnt/legato
S02mount_early: Executing mount_early_userrw_start... 
S02mount_early: Mounting swirw file system as UBIFS
S02mount_early: Trying to mount UBIFS on /mnt/userrw using [usrquota,grpquota,rw] mount options...

UBI device number 4, total 100 LEBs (25395200 bytes, 24.2 MiB), available 2 LEBs (507904 bytes, 496.0 KiB), LEB size 253952 bytes (248.0 KiB)

S02mount_early: Performing quota check on file system mounted at /mnt/userrw

S02mount_early: UBIFS volume successfully mounted on /mnt/userrw
S02mount_early: swirw mounted to /mnt/userrw

S03confighw.sh: Kernel internal entropy pool filler is available, increasing write_wakeup_threshold to 3072

Starting system message bus: dbus.
Loading modules: S07mount_unionfs: RO rootfs fudge allowed.

S07mount_unionfs: Overlay over /etc is allowed
S07mount_unionfs: Using timezone [Universal].
Mounting local filesystems...
[   12.365605] UBIFS error (pid: 534): cannot open "ubi0:usrfs", error -19mount: mounting ubi0:usrfs on /usr failed: No such device
mount modem from partition modem
MTD : Detected block device : /firmware for modem

UBI device number 1, total 128 LEBs (32505856 bytes, 31.0 MiB), available 20 LEBs (5079040 bytes, 4.8 MiB), LEB size 253952 bytes (248.0 KiB)

[   12.740130] usb 1-1: device descriptor read/64, error -110

Initializing random number generator...
Switching to composition sierra_dev (1199:68C0)

[   14.922169] enable_store: android_usb: already disabled

SOFTAP_W_DUN: Y

Configuring network interfaces... 
[   15.395206] gbam_connect_work: gbam_connect_work: Bam channel is not ready
[   15.407887] qti_ctrl_queue_notify: qti_ctrl_queue_notify: rmnet ctrl file handler cd656300 is not open


done.
Starting syslogd/klogd: 
done
ifconfig: SIOCGIFFLAGS: No such device
Starting diagrebootapp: 
done
$Starting qcom_time:
starting time-daemon
Starting time_services: done

Legato start sequence
start_at_cmux_le: Starting DS_MUX: 
restart_at_uart: Mapped UART1 for AT service

start_at_cmux_le: Done start_at_cmux_le script.

update-ld-cache: Removing stale mount [/etc/ld.so.conf]...

update-ld-cache: Removing stale mount [/etc/ld.so.cache]...

update-ld-cache: Updating ld.so.cache using [/legato/systems/current/lib]...
update-
ld-cache: Updating /etc/ld.so.cache ...

[   18.247159] i2c-msm-v2 78b8000.i2c: msm_bus_scale_register_client(mstr-id:86):0xd (ok)

[   18.285480] i2c-msm-v2 78b8000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x3a MSTR_STS:0x001363c8 OPER:0x00000090
[   18.300582] i2c-msm-v2 78b8000.i2c: NACK: slave not responding, ensure its powered: msgs(n:1 cur:0 tx) bc(rx:0 tx:2) mode:FIFO slv_addr:0x3a MSTR_STS:0x001363c8 OPER:0x00000090

update-ld-cache: Removing stale mount [/etc/ld.so.cache]...

[   20.409575] mdm9607-asoc-snd soc:sound-wm8944: Defering mdm_asoc_machine_probe, q6_state 0

[   20.443584] M-Notify: General: 7
[   20.561314] diag: In diag_send_feature_mask_update, control channel is not open, p: 0, c0fb49d4

Jan  6 00:01:54 swi-mdm9x28-wp user.info Legato: le_pa_start: Initialized QMI
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp: qmi_client_init_instance status retry : 8
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp:   qmi_client_init_instance....
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp: qmi_client_init_instance status: 0, num_retries: 9, retryCnt: 1
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp: qmi_client_register_error_cb status: 0
Jan  6 00:01:54 swi-mdm9x28-wp user.info 
swiapp: qmi_client_notifier_init status: 0
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp: qmi_client_notifier_init status: -19
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp: result : 0 \0x09 ,Init step :1 \0x09 ,qmiErrorCode: 0
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp:   Back to main.
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp:  tryinit complete with connectresult: 0
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp: 
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp:   TrtyInit: retryCnt: 1
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp: type - 2 do nothing
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp: result : 0 \0x09 ,Init step :2 \0x09 ,qmiErrorCode: 0
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp:   Back to main.
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp:  tryinit complete with connectresult: 0
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp: Trying to register 9 commands:
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp: cmd0: +CFUN
Jan  6 00:01:54 swi-mdm9x28-wp user.info swiapp: sending QMI_AT_REG_AT_CMD_FWD_REQ_V01 message

[   28.031021] usb 1-1: device descriptor read/64, error -110

Jan  6 00:01:56 swi-mdm9x28-wp user.err kernel: [   28.031021] usb 1-1: device descriptor read/64, error -110
Jan  6 00:01:56 swi-mdm9x28-wp user.info kernel: [   28.261223] usb 1-1: new high-speed USB device number 3 using msm_hsic_host

Jan  6 00:01:59 swi-mdm9x28-wp user.info kernel: [   30.463322] gpio_check_and_wake: wake-n_gpio26 STATE=WAKEUP
Jan  6 00:01:59 swi-mdm9x28-wp user.info kernel: [   30.473328] swimcu_calibrate_event_handle: MCU calibrate completed with remaining time 0
Jan  6 00:01:59 swi-mdm9x28-wp user.info kernel: [   30.473356] swimcu_lpo_calibrate_calc: MCU time=30000 vs MDM time=30041 
Jan  6 00:01:59 swi-mdm9x28-wp user.info kernel: [   30.473376] gpio_check_and_wake: wake-n_gpio26 STATE=SLEEP

[   33.401039] usb 1-1: device descriptor read/64, error -110

Jan  6 00:02:02 swi-mdm9x28-wp user.err kernel: [   33.401039] usb 1-1: device descriptor read/64, error -110

[   48.691024] usb 1-1: device descriptor read/64, error -110

Jan  6 00:02:17 swi-mdm9x28-wp user.err kernel: [   48.691024] usb 1-1: device descriptor read/64, error -110
Jan  6 00:02:17 swi-mdm9x28-wp user.info kernel: [   48.801154] usb usb1-port1: attempt power cycle
Jan  6 00:02:17 swi-mdm9x28-wp user.info kernel: [   49.241042] usb 1-1: new high-speed USB device number 4 using msm_hsic_host

[   50.530995] wait_for_irsc_completion: waiting for IPC Security Conf.

[   51.311018] wait_for_irsc_completion: waiting for IPC Security Conf.

Jan  6 00:02:19 swi-mdm9x28-wp user.err kernel: [   50.530995] wait_for_irsc_completion: waiting for IPC Security Conf.
Jan  6 00:02:19 swi-mdm9x28-wp user.err kernel: [   51.311018] wait_for_irsc_completion: waiting for IPC Security Conf.

[...]

What is the return of “ifconfig ecm0”?

What is the return of the following:

  1. microcom /dev/ttyAT
  2. AT!ENTERCND=“A710”
  3. AT!USBCOMP?
  4. AT!USBCOMP=?
  5. Ctrl + x to quit the microcom program
ifconfig ecm0

ecm0: erreur lors de la recherche d'infos sur l'interface: Périphérique non trouvé

With cutecom on /dev/ttyUSB3
ati

Manufacturer: Sierra Wireless, Incorporated
Model: WP7702
Revision: SWI9X06Y_02.32.02.00 c2e98c jenkins 2019/08/30 07:28:21
IMEI: 352653090204686
IMEI SV: 4
FSN: 4L935170020910
+GCAP: +CGSM

OK

AT!ENTERCND="A710"

OK

AT!USBCOMP?

Config Index: 1
Config Type: 1 (Generic)
Interface bitmask: 0008010D (diag,nmea,modem,rmnet0,ecm)

OK

AT!USBCOMP=?

!USBCOMP:
AT!USBCOMP=,,
- configuration index to which the composition applies, should be 1

- 1:Generic

- DIAG - 0x00000001,
NMEA - 0x00000004,
MODEM - 0x00000008,
RAWDAT - 0x00000040,
RMNET0 - 0x00000100,
RMNET1 - 0x00000400,
RMNET2 - 0x00000800,
AUDIO - 0x00010000,
ECM - 0x00080000,
NCM - 0x00400000,
e.g.
9 - diag,modem interfaces enabled
10D - diag,nmea,modem,rmnet0 interfaces enabled

OK

The ecm interface on module seems not started.
Please try configEcm command
https://docs.legato.io/latest/toolsTarget_configEcm.html

the configEcm command has to be launched on the target but I cannot connect to it
And I had the same ecm0 error message with the working board

then how can you communicate on working board in case the ecm0 interface is not started?

Does it has UART console on MangOH yellow board?

Seems to be through this interface:
enp0s20f0u2i19: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether e2:d4:fc:b4:57:18 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

is this renamed from usb0 on Linux PC?
You can check in dmesg.

I believe from the problematic board, there should also be usb0 enumerated in PC as ECM interface has bee enabled in AT!USBCOMP

in dmesg

cdc_ether 1-2:1.19 enp0s20f0u2i19: renamed from usb0

Following by:
ADDRCONF(NETDEV_UP): enp0s20f0u2i19: link is not ready

And in the working one I have this, but not in the other:
ADDRCONF(NETDEV_CHANGE): enp0s20f0u2i19: link becomes ready

ifconfig enp0s20f0u2i19

Problematic board:
enp0s20f0u2i19: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 6e:bc:30:04:a6:6f txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)

Working one:
enp0s20f0u2i19: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.2.3 netmask 255.255.255.0 broadcast 192.168.2.255
inet6 fe80::552:4bc8:eb00:da74 prefixlen 64 scopeid 0x20
ether 92:d9:1c:7d:2e:93 txqueuelen 1000 (Ethernet)
RX packets 11 bytes 1220 (1.2 KB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 47 bytes 7438 (7.4 KB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

how about “sudo ifconfig enp0s20f0u2i19 192.168.2.3” ?
and then try to ping module by “ping 192.168.2.2” ?

BTW is there any UART console on your MangOH yellow board?

PING 192.168.2.2 (192.168.2.2) 56(84) bytes of data.
From 192.168.2.3 icmp_seq=1 Destination Host Unreachable

I get the logs from USB on the other port, I do not really understand your UART question

seems the module’s ecm0 is not yet ready for IP 192.168.2.2.

there is a USB port in the mangoh yellow board, I believe that is UART console

Therfore what’s your advice?

Of course connect usb cable to see if you can enter console

Yes it is the USB port I used to retrieve all the logs I put in here
You mean write commands through this port ?

This is the uart console, you can check " ifconfig ecm0"