About the GPS reading

shahahsanuzzamanmdta · August 19, 2020, 5:48pm

Hi, i am new in working with mangOH RED. I am testing the user guide and once i connect the SIM at first, it was showing the correct GPRMC reading. But suddenly, it shows empty. I did not get it, it is the problem with the SIM or configuration? Could someone help me in this issue?

Akshaysk · August 25, 2020, 5:54am

Hi @shahahsanuzzamanmdta ,
Did you connect the GPS Antenna ? Sim configurations has got nothing to do with GPS data .
Please make sure you are connecting GPS antenna in the correct slot .

Regards

Ak

shahahsanuzzamanmdta · August 25, 2020, 5:41pm

Hi, thanks. Yes, connected the GPS antenna and got results as i explained. But GPRMC reading goes out after a while.

Akshaysk · August 26, 2020, 5:28am

Hi @shahahsanuzzamanmdta ,
Can you share the NMEA sentences you are getting ? what is the value of total number of Satellites in view (Found in GPGSV sentence) .

shahahsanuzzamanmdta · August 26, 2020, 1:58pm

https://drive.google.com/file/d/1duPsra9uBQRfa2dvppW2AKzqXyDOo4R6/view?usp=sharing, https://drive.google.com/file/d/1fC-whp1GrwM9WVaHf6ZWJDf73TimMzST/view?usp=sharing

Akshaysk · August 27, 2020, 5:16am

@shahahsanuzzamanmdta which module are you using ? what is the firmware version ? Did you try testing at different locations ?

shahahsanuzzamanmdta · August 27, 2020, 1:58pm

@Akshaysk it is 7601G module and if i change the location then it works that means need to move after a while always? or need to change the gps cofig? the firmware is updated one.

Akshaysk · August 28, 2020, 12:57pm

Hi @shahahsanuzzamanmdta ,
Ideally you should be able to get the RMC values continuously if you have the fix .

shahahsanuzzamanmdta · August 28, 2020, 9:52pm

I am trying to use AT commands to have the GPS readings. Could you please help me in this issue? How can i send AT commands as like arduino?

Akshaysk · August 31, 2020, 7:44am

What is your application ? The module has a dedicated application processor , framework to do the job for you . why don’t you use the API’s from framework .

shahahsanuzzamanmdta · August 31, 2020, 4:21pm

Thanks for your help. The application is to read GPS location and send SMS to a phone number.

Akshaysk · September 1, 2020, 5:22am

@shahahsanuzzamanmdta ,
You can find a reference legato code in the below link . Kindly go through the code and modify it based on your requirements .

shahahsanuzzamanmdta · September 1, 2020, 2:36pm

Thanks for your help.

I would like to install the apps redSensor and redCloud into mangOH from

to read the sensor data reading into the Airvantage dashboard.

Could you please help me to know how to install thease two apps into developer studio 5.3.1 and legato is WP76 R12 18.10.3? Thanks.

shahahsanuzzamanmdta · September 3, 2020, 9:48pm

Hi, i tried to run the code of gps and getting errors.

github.com

legatoproject/legato-af/blob/master/apps/sample/textLoc/textLocComponent/textLoc.c

//--------------------------------------------------------------------------------------------------
/** @file textLoc.c
 *
 * This app illustrates a sample usage of ultra low power mode API. This app reads the current gps
 * location and then sends it as a text message to a destination cell phone number.  Once the text
 * message has been sent, the device enters ultra low power mode.  The device will wake up from
 * ultra low power mode after a configurable delay.
 *
 * @note This app expects destination cell number to be specified in environment variable section
 * of adef file. If nothing specified in environment variable, it will send message to a default
 * non-existent phone number.
 *
 * Copyright (C) Sierra Wireless Inc.
 */
//--------------------------------------------------------------------------------------------------

#include "legato.h"
/* IPC APIs */
#include "interfaces.h"

This file has been truncated. show original

The picture is attached.

Could someone please help with this issue?

Akshaysk · September 7, 2020, 4:50am

@shahahsanuzzamanmdta ,
Did you install the Legato packages ?

shahahsanuzzamanmdta · September 8, 2020, 12:34am

Hi, thanks. i have legato 18.10.3.wp76xx-docker-201903041325 installed package. Is there any other specific legato package need to install to run textLoc.c? Thanks in advance.

Akshaysk · September 8, 2020, 5:07am

Hi @shahahsanuzzamanmdta ,
No issues you can continue with the current setup . Please verify your adef and cdef files to resolve the errors faced . You can find similar issues reported in https://forum.legato.io/ Please go through them .

Topic		Replies	Views
No satellites found & inaccurate LatLong with GPS antenna attached mangOH Red	21	2934	July 18, 2018
GPS Active Antenna mangOH Red	3	769	November 30, 2017
GPS related issue mangOH Green	43	857	August 17, 2022
Time update and synchronization mangOH Red	7	1201	April 17, 2019
HL7800 GNSS Fix Problems mangOH Red	1	473	March 8, 2020

About the GPS reading

Related topics