Is it possible to enable Diag port using AT!USBCOMP command?
I tried but getting “ERROR”
at!usbcomp=1,9010D
ERROR
at!usbcomp?
Config Index: 1
Config Type: 1 (Generic)
Interface bitmask: 0009010C (nmea,modem,rmnet0,audio,ecm)
OK
at!usbcomp=1,1,9010D
ERROR
at!usbcomp=1,1,9010D
ERROR
You need to first type
AT!entercnd=“A710”
yes i did that. But still getting error.
at!entercnd=“A710”
OK
at!usbcomp=1,9010D
ERROR
at!usbcomp?
Config Index: 1
Config Type: 1 (Generic)
Interface bitmask: 0009010C (nmea,modem,rmnet0,audio,ecm)
OK
at!usbcomp=1,1,9010D
ERROR
at!usbcomp=1,1,9010D
ERROR
AT
OK
What is return of at!usbcomp=?
at!entercnd=“A710”
OK
at!usbcomp=?
!USBCOMP:
AT!USBCOMP=,,
- configuration index to which the composition applies, s1
- 1:Generic
- DIAG - 0x00000001,
NMEA - 0x00000004,
MODEM - 0x00000008,
RAWDAT - 0x00000040,
RMNET0 - 0x00000100,
RMNET1 - 0x00000400,
RMNET2 - 0x00000800,
AUDIO - 0x00010000,
ECM - 0x00080000,
NCM - 0x00400000,
e.g.
9 - diag,modem interfaces enabled
10D - diag,nmea,modem,rmnet0 interfaces enabled
OK
Do you change the usbcomp value before?
I remember the dm port can be seen by default.
Yes wanted to enable audio, so tried 9010C .
Now is it possible to enable diag ?
Seems no, according to your test result…
You might need to contact distributor
Thanks for the info.
If the diag is disabled will there be any issues with atd; command ?
I am trying to do so but its giving me error.
atd9844371816;
ERROR
at+cops?
+cops: 0,0,“IND airtel airtel”,7
OK
at+creg?
+CREG: 0,1
OK
Also the
root@swi-mdm9x28-wp:~# cm radio status
Power: ON
Current Network Operator: IND airtel
Current RAT: LTE network (LE_MRC_RAT_LTE)
Status: Registered, home network (LE_MRC_REG_HOME)
Signal: Very strong signal strength (5)
PS: Packet Switched Registered, home network (LE_MRC_REG_HOME)
Did you enter the atd in microcom console program or the usb AT port?
Did your operator support voice call?
The atd is enterd on the USB AT port.
This is a working sim card.
Maybe your module is non volte modem.
Please see here
tried to follow the link, but few at comands not available.
at!entercnd=“A710”
OK
at!fmw?
ERROR
at!gstatus?
!GSTATUS:
Current Time: 1617 Temperature: 42
Modem Mitigate Level: 0 ModemProc Mitigate Level: 0
Reset Counter: 1 Mode: ONLINE
System mode: LTE PS state: Attached
IMS reg state: UNKNOWN IMS mode: Not Support
IMS Srv State: UNKNOWN SMS,UNKNOWN VoIP
LTE band: B1 LTE bw: 10 MHz
LTE Rx chan: 240 LTE Tx chan: 21626
LTE CA state: INACTIVE
EMM state: Registered Normal Service
RRC state: RRC Idle
PCC RxM RSSI: -64 RSRP (dBm): -97
PCC RxD RSSI: -64 RSRP (dBm): -96
Tx Power: 0 TAC: 2152 (8530)
RSRQ (dB): -15 Cell ID: 00049921 (301345)
SINR (dB): -2.4
OK
at+cgact?
+CGACT: 1,1
OK
at!entercnd=“A710”
OK
at!fmpath?
ERROR
at!fmpath=?
ERROR
at+cgdcont?
+CGDCONT: 1,“IPV4V6”,“internet”,“0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0”,0,0,0,0
OK
at+cgdcont=2,“IPV4V6”,“ims”
OK
AT$qcpdpimscfge?
$QCPDPIMSCFGE: 1 , 0 , 0 , 0
$QCPDPIMSCFGE: 2 , 0 , 0 , 0
OK
at!reset
OK
at!gstatus?
!GSTATUS:
Current Time: 520 Temperature: 44
Modem Mitigate Level: 0 ModemProc Mitigate Level: 0
Reset Counter: 1 Mode: ONLINE
System mode: LTE PS state: Attached
IMS reg state: UNKNOWN IMS mode: Not Support
IMS Srv State: UNKNOWN SMS,UNKNOWN VoIP
LTE band: B1 LTE bw: 10 MHz
LTE Rx chan: 240 LTE Tx chan: 21626
LTE CA state: INACTIVE
EMM state: Registered Normal Service
RRC state: RRC Idle
PCC RxM RSSI: -64 RSRP (dBm): -97
PCC RxD RSSI: -61 RSRP (dBm): -92
Tx Power: 0 TAC: 2152 (8530)
RSRQ (dB): -14 Cell ID: 00049921 (301345)
SINR (dB): 2.8
OK
at+cgact?
+CGACT: 1,1
+CGACT: 2,0
OK
atd9844371816;
ERROR
“at!fmxxx commands are not accessible to users outside of Sierra Wireless which is why they did not work.”
Already stated in the link.
You need to buy a module that enable volte.
So there is no way that i can do a “ATDnn;” on this module ?
The whole idea is to enable a Call and also enable wifi.
Request any suggestion to get a call working other than buying module.
no idea on old module.
I just make a test on my module, no problem is found for voice call.
at!gstatus?
!GSTATUS:
Current Time: 146 Temperature: 31
Modem Mitigate Level: 0 ModemProc Mitigate Level: 0
Reset Counter: 1 Mode: ONLINE
System mode: LTE PS state: Attached
LTE band: B3 LTE bw: 20 MHz
LTE Rx chan: 1385 LTE Tx chan: 19385
LTE CA state: INACTIVE
EMM state: Registered Normal Service
RRC state: RRC Idle
IMS reg state: No Srv
PCC RxM RSSI: -78 RSRP (dBm): -107
PCC RxD RSSI: -95 RSRP (dBm): -135
Tx Power: 0 TAC: 0462 (1122)
RSRQ (dB): -8 Cell ID: 06745D16 (108289302)
SINR (dB): 7.8
OK
ati3
Manufacturer: Sierra Wireless, Incorporated
Model: WP7607-1
Revision: SWI9X07Y_02.18.05.00 000000 jenkins 2018/07/19 17:40:21
IMEI: 359780080500170
IMEI SV: 5
FSN: V2842570321010
+GCAP: +CGSM
OK
atd28245238;
OK
NO CARRIER
I enabled only GSM using AT+KSRAT=1 and then it started working.
Can you let me know the troubles if diag port is not enabled ?
Any features cannot be used?
you cannot take log in case there is network issue.
You cannot use all the Qualcomm tool like QPST.
Ok. Thank you for the information. Let me check if the diag canbe enabled.