# mangOH Yellow Getting Started - Where Next? **URL:** \ **Category:** mangOH Yellow\ **Created:** [October 1, 2019, 5:50pm UTC](https://mangoh.discourse.group/t/mangoh-yellow-getting-started-where-next/2952 "2019-10-01T17:50:10Z")\ **Posts on this page:** 11\ **Page:** 1
**Author:** ![awneil](https://sea2.discourse-cdn.com/flex016/user_avatar/mangoh.discourse.group/awneil/32/486_2.png) [@awneil](https://mangoh.discourse.group/u/awneil)\ **Post date:** [October 1, 2019, 5:50pm UTC](https://mangoh.discourse.group/t/mangoh-yellow-getting-started-where-next/2952/1 "2019-10-01T17:50:11Z")
So the mangOH yellow arrived: [https://twitter.com/antronicsltd/status/1174410588254085123](https://twitter.com/antronicsltd/status/1174410588254085123) šŸ˜ƒ Been through the Getting Started Guide (Rev 1.01); only one big error: the On/Off switch is documented the wrong way around! An observation: p9 says, > When the mangOH Yellow is powered, the Power LED turns solid green, and then all three LEDs will begin blinking in sequence when the module has finished booting up. What I actually see is that the Power/Network/Cloud LED stays permanently green while the other two LEDs cycle through: - Both Off - RGB = Greem - RGB = Blue - Both off - Generic LED = Yellow (not green) Ping works, and I see console output, although thereā€™s no response in the DM port - should there be? But where should I go next? The obvious next steps would seem to be to log-in at the console, and/or issue some AT commands. But there is nothing on the ā€˜Get Startedā€™ page to say where next ā€¦ ---
**Author:** ![awneil](https://sea2.discourse-cdn.com/flex016/user_avatar/mangoh.discourse.group/awneil/32/486_2.png) [@awneil](https://mangoh.discourse.group/u/awneil)\ **Post date:** [October 1, 2019, 5:55pm UTC](https://mangoh.discourse.group/t/mangoh-yellow-getting-started-where-next/2952/2 "2019-10-01T17:55:08Z")
> [@awneil](#): > > the Getting Started Guide (Rev 1.01); That is, the PDF. Just had a quick look at the [Online version](http://mangoh.io/uploaded-documents/Reference/mangOH%20Yellow/Discover/Getting%20Started/41113347%20mangOH%20Yellow%20GSG%20-%20HTML5-Responsive%20HTML5/#t=41113347_mangOH_Yellow_GSG_-_HTML5%2F41113347_Tut_Quick_Start%2F41113347_Tut_Quick_Start.htm) - which does seem to go further ā€¦ ---
**Author:** ![asyal](https://sea2.discourse-cdn.com/flex016/user_avatar/mangoh.discourse.group/asyal/32/78_2.png) [@asyal](https://mangoh.discourse.group/u/asyal)\ **Post date:** [October 1, 2019, 9:00pm UTC](https://mangoh.discourse.group/t/mangoh-yellow-getting-started-where-next/2952/3 "2019-10-01T21:00:52Z")
Did you manage to connect to Octave? We will fix the document on the on/off button. ---
**Author:** ![awneil](https://sea2.discourse-cdn.com/flex016/user_avatar/mangoh.discourse.group/awneil/32/486_2.png) [@awneil](https://mangoh.discourse.group/u/awneil)\ **Post date:** [October 2, 2019, 10:14am UTC](https://mangoh.discourse.group/t/mangoh-yellow-getting-started-where-next/2952/4 "2019-10-02T10:14:29Z")
Octave isnā€™t even mentioned in the PDF ā€˜Getting Startedā€™ guide ---
**Author:** ![asyal](https://sea2.discourse-cdn.com/flex016/user_avatar/mangoh.discourse.group/asyal/32/78_2.png) [@asyal](https://mangoh.discourse.group/u/asyal)\ **Post date:** [October 2, 2019, 1:20pm UTC](https://mangoh.discourse.group/t/mangoh-yellow-getting-started-where-next/2952/5 "2019-10-02T13:20:23Z")
Do you have the right gettting started ? šŸ™‚ What does page 15 show up as ? ---
**Author:** ![awneil](https://sea2.discourse-cdn.com/flex016/user_avatar/mangoh.discourse.group/awneil/32/486_2.png) [@awneil](https://mangoh.discourse.group/u/awneil)\ **Post date:** [October 2, 2019, 2:29pm UTC](https://mangoh.discourse.group/t/mangoh-yellow-getting-started-where-next/2952/6 "2019-10-02T14:29:06Z")
Ha ha -no, it was the ā€œUser Guideā€ ! However, if I use the online Getting Started, when I get to the 'Device Registration;: ![image](https://us1.discourse-cdn.com/flex016/uploads/mangoh/original/1X/95860d049d5103a74dab0dcb688ed5126755ab19.png) pressing ā€˜Submitā€™ just takes me straight back to the ā€˜Getting Startedā€™ page: ![image](https://us1.discourse-cdn.com/flex016/uploads/mangoh/original/1X/89a6a742adb8fbc3fdadccc9b8626b69e48579a2.png) šŸ˜’ ---
**Author:** ![asyal](https://sea2.discourse-cdn.com/flex016/user_avatar/mangoh.discourse.group/asyal/32/78_2.png) [@asyal](https://mangoh.discourse.group/u/asyal)\ **Post date:** [October 2, 2019, 2:59pm UTC](https://mangoh.discourse.group/t/mangoh-yellow-getting-started-where-next/2952/7 "2019-10-02T14:59:35Z")
Okā€¦ can u let us know the experience with the Getting Started Guide? ---
**Author:** ![awneil](https://sea2.discourse-cdn.com/flex016/user_avatar/mangoh.discourse.group/awneil/32/486_2.png) [@awneil](https://mangoh.discourse.group/u/awneil)\ **Post date:** [October 2, 2019, 3:17pm UTC](https://mangoh.discourse.group/t/mangoh-yellow-getting-started-where-next/2952/8 "2019-10-02T15:17:54Z")
Sure - will do ā€¦ ---
**Author:** ![awneil](https://sea2.discourse-cdn.com/flex016/user_avatar/mangoh.discourse.group/awneil/32/486_2.png) [@awneil](https://mangoh.discourse.group/u/awneil)\ **Post date:** [October 2, 2019, 3:20pm UTC](https://mangoh.discourse.group/t/mangoh-yellow-getting-started-where-next/2952/9 "2019-10-02T15:20:01Z")
> [@awneil](#): > > the other two LEDs cycle through: > > - Both Off > - RGB = Greem > - RGB = Blue > - Both off > - Generic LED = Yellow (not green) Now got to the ā€˜helloā€™ demo. The LEDs section seems to confirm that the Red in the RGB LED is not working ---
**Author:** ![awneil](https://sea2.discourse-cdn.com/flex016/user_avatar/mangoh.discourse.group/awneil/32/486_2.png) [@awneil](https://mangoh.discourse.group/u/awneil)\ **Post date:** [October 2, 2019, 10:17pm UTC](https://mangoh.discourse.group/t/mangoh-yellow-getting-started-where-next/2952/10 "2019-10-02T22:17:46Z")
> [@asyal](#): > > can u let us know the experience with the Getting Started Guide Page 6 - Registration The ā€˜Device Registrationā€™ doesnā€™t actually seem to do anything - just takes you to the page with the info about the device you select. If thatā€™s the intended operation, it could be better explained. Page 7 - Kit contents Mine was missing the M2 screws! Page 8 - Overview This is good - like it šŸ™‚ (the power selection jumper is not identified) Page 9 - Windows Drivers I didnā€™t do this - Windows found all the drivers itself Pages 9-12 Similar to whatā€™s in the User Guide, but missing a few steps; eg, - power supply selection - connecting the antenna - the on/off switch Pages 13-14 Local connection All fine Page 15 - Octave free trial doesnā€™t reflect the current experience Pages 15-18 - Send to Octave I couldnā€™t get this to work: > [@Octave - Register mangOH Yellow?](https://mangoh.discourse.group/t/octave-register-mangoh-yellow/2956/13): > > OK - great. So, for now, I am able to send commands to the Yellow - to control LEDs & buzzer - but donā€™t seem to be getting anything from it. It is still saying, ā€œNo blueprint deployed yetā€ - is having a blueprint essential ? The Octave documentation isnā€™t too helpful as itā€™s focused only on the Red, and does not quite reflect what the interface actually looks like now. Pages 18-20 Control from Octave worked fine. It references the Octave developer site, but that is purely Red-focussed, and doesnā€™t quite reflect the actual online experience. ---
**Author:** ![Kas.Lewis](https://avatars.discourse-cdn.com/v4/letter/k/e9a140/32.png) [@Kas.Lewis](https://mangoh.discourse.group/u/Kas.Lewis)\ **Post date:** [December 10, 2019, 9:17pm UTC](https://mangoh.discourse.group/t/mangoh-yellow-getting-started-where-next/2952/11 "2019-12-10T21:17:32Z")
> [@awneil](#): > > Page 7 - Kit contents > Mine was missing the M2 screws! Mine was also missing the screws. I just assumed since mine was a demo unit or pre production (I have some wires to correct for missing or incorrect traces) that that would be the reason for the missing screws. On page 8, there is mention of a buzzer, the picture shows a board that has the buzzer unpopulated while the actual board (at least mine) has the buzzer populated. On page 7, it mentions that the WP module is soldered down, mine is the same as on my red and green. Both of those had a ā€œcageā€ to hold the module and the module could be removed with a special tool. The other issue Iā€™m having is trying to update the firmware. If I do over the air there are a LOT of options with no useful naming convention. Some are octave\_redā€¦ others red\_wp and still others mangoh\_wp. DO they ALL work on the yellow, what about the green? Is there away to update the firmware not using Octave? Kas